9
2
1
Use this image area for
full size breakups.This
image will always be in the
light beam. Use an identical
or different pattern in the
fixture’s gobo slot to create
additional effects.
Maximum available image
area: 4 5/8” (L) x 3” (W)
117.475mm (L) x 76.2mm (W)
2
Images in this area will
drop into light beam but
not be centered.
Maximum available image
area: 1 1/2” (L) x 3” (W)
38.1mm (L) x 76.2mm (W)
3
Images in this area will
rise into the light beam
but not be centered.
Maximum available image
area: 1 1/2” (L) x 3” (W)
38.1mm (L) x 76.2mm (W)
4
Use this area for images
that will move up and
down within the light beam.
One, two, or three lines of
text can go into this area.
One line at a time or all
three lines at once can be
projected here using the
fixture shutters.
Maximum available image
area: 1 1/2” (L) x 3” (W)
38.1mm (L) x 76.2mm (W)
5
Use this area for
images that will
disappear at the top of
the light beam. Use in
conjunction with area
#6 to have one pattern
completely replace
another pattern in the
center of the light beam.
Maximum available image
area: 5/8” diameter
15.875mm diameter
6
Use this area for
images that will
disappear at the bottom
of the light beam. Use
in conjunction with area
#5 to have one pattern
completely replace another
pattern in the center of the
light beam.
Maximum available image
area: 5/8” diameter
15.875mm
diameter
Six image areas on Vertical gobo.
Smart Move Vertical Troubleshooting
• Unit does not move gobo.
•
Check 110 volt outlet by plugging in a known working lighting fixture.
•
If fixture operates, plug Smart Move power supply in and check for
24 volts DC between the tip and ring of the ¼
”
power plug.
•
If 24 volts is present, check to see if the address switches are
set to 01 through 17. Address 00 is not a valid setting.
•
Smart Moves set at the slowest speed may appear to be not working.
Rotate speed knob to highest setting.
•
If the motor is running but there is no vertical movement check
the set screw on the drive arm. If loose, tighten.
• Unit is noisy.
•
It is normal for a Smart Move Vertical to produce minimal noise when
brand new. After heating up once in a lit fixture, the Teflon
components
“
set
”
. All units operate quietly after this initial heat cycle.
•
Smart Move Verticals have been designed and tested for long
periods of normal operation. In some extreme cases, the
Teflon bushing will wear. Teflon bushings and spacer strips
are available in the Smart Move Vertical maintenance kit.
DMX
• Unit does not move gobo.
•
Check 24 volt DC power source. If any other Smart Move DMX or
Smart Color DMX products are available, plug them into the power
supply to confirm 24 volts DC. If no other units are avail able check
for 24 volts DC between pin 2 and pin 3 on the 4 pin XLR cable.
•
If 24 volts is present, check to see if the address switches are set
to 001 through 512. Address 000 is not a valid setting.
•
Smart Moves set at the slowest speed may appear to be not
working. Rotate speed knob to highest setting.
•
Set address switches to
“
701
”
. This setting will operate the
Vertical in stand alone mode in effect 01.
•
If unit operates in stand alone mode but not in DMX control mode
verify that the unit is not in the indexing or effects mode. The Smart
Move Vertical DMX requires three DMX channels. Make sure that the
second and third channels are receiving 0% output.
•
If the motor is running but there is no vertical movement check the
set screw on the drive arm. If loose, tighten.
• Unit is noisy.
•
It is normal for a Smart Move Vertical to produce minimal noise
when brand new. After heating up once in a lit fixture, the Teflon
components
“
set
”
. All units operate quietly after this initial heat cycle.
•
Smart Move Vertical have been designed and tested for long
periods of normal operation. In some extreme cases, the Teflon
bushing will wear. Teflon bushings and spacer strips are avail
able in the Smart Move Vertical maintenance kit.
