Apollo 7000ETL Installation Manual Download Page 4

APPLICATIONS 

 

 

The 

Apollo 

Model 7000ETL Slide Gate Operator is designed to handle a slide gate 

up to 22 feet in total length (accomodates a 20 foot drive) and 600 Lbs. A 
professional fence or gate dealer is recommended to assure proper installation. 

Apollo Gate Operators

 are available only through qualified dealers with an 

outstanding reputation in the fence and gate industry. These dealers will be able to 
recommend the proper equipment for particular applications. 

Apollo Gate 

Operators 

are 12 Volt DC (

Direct Current

) powered. A 12 Volt 33 ampere hour 

(minimum) sealed battery is recommended. There are several advantages with 12 
Volt DC systems: 
 

• 

Low voltage virtually eliminates risk of electrical shock. 

• 

Battery powered operators can provide up to 200 operations in the event of 
power outages. 

• 

The battery may be recharged with a trickle charger or by solar energy  
(Electrical battery chargers should have a class 2 transformer rating).  

 

If a trickle charger is used and a standard electrical outlet is not readily available, a 
licensed electrician will be required for proper electrical hook up. 
 
The following table should be used as a guide for capacity of operation of operators 
only, additional options may reduce the the daily usage. 

Please note that the charge 

capability of solar panels will vary with different geographical locations.  
 

                              Daily Cycles       

1-10  1-20  1-40  1-60  1-80  80+ 

5 watt solar panel 

 

 

 

 

 

10 watt solar panel 

 *        

20 watt solar panel 

(requires 5310 regulator) 

 

 

 

 

 

30 watt solar panel 

(requires 5310 regulator) 

   *   

40 watt solar panel 

(requires 5310 regulator) 

 

 

 

 

 

1.5 amp battery charger 

    *  

10 amp battery charger 

 

 

 

 

 

Note: Double the amount of solar panels for Dual Gate Operators. 

Summary of Contents for 7000ETL




















Reviews: