![API W250 Setup And Operation Download Page 1](http://html1.mh-extra.com/html/api/w250/w250_setup-and-operation_2953438001.webp)
Miller Manufacturing, Glencoe, MN 55336 USA • www.miller-mfg.com
Setup and Operation
SPECIFICATIONS
W250/DT250/BDT250: 250 watts, 120 VAC, 60 Hz
W500/DT500: 500 watts, 120 VAC, 60 Hz
WARNING
1. Have a qualified electrician install a properly
grounded receptacle outlet, acceptable for
outdoor use and protected from snow and
rain, immediately adjacent to the location
where the heater will be used.
2. Route the supply cord and locate the
heater so as to be protected from damage
by livestock.
3. Do not use extension cords.
4. Inspect cord before using.
5. Unplug heater at receptacle outlet when not
in use or before removing from tank.
6. Store heater indoors after winter season.
7. Connect to properly grounded outlets only.
8. Heating element MUST be completely
submerged while in use to prevent risk of fire
hazard.
9. Do not tether unit.
10.
Connect only to a circuit that is protected
by a Ground Fault Circuit Interrupter
(GFCI).
This is a sensitive device that cuts
off the electricity if there is any leakage of
current. This device may be obtained from
any electrician or hardware store.
IMPORTANT
This product is approved for use only with the
LOCKNDRY® extension cord. It is not approved
for use with any other extension cords. The
plug on this product is specially designed
to mate with the LOCKNDRY® cord to form
a water-resistant seal. See the LOCKNDRY®
instructions at right.
OPERATION
Simply place the unit into the water that you
wish to keep de-iced. Connect the cord to a
properly grounded, GFCI-protected receptacle
while observing the cautions above. The unit
will turn on when the water temperature
approaches freezing conditions and will heat
the water 10 to 20 degrees Fahrenheit before
turning off.
Multiple thermostats within the unit monitor
water temperature as well as guard against
overtemp conditions. Please note: the unit
will not turn on unless the water temperature
is approaching freezing. If you wish to test
the unit, you must place it in a freezer for 15
minutes to get it cold enough to turn on.
WARRANTY
This de-icer is warranted for a period of 1
year from the date of purchase. If you believe
your de-icer is defective and still within the
warranty period, return it to the factory or
place of purchase for inspection and possible
replacement. The warranty is voided if (1)
the ground terminal on the plug has been
removed, (2) excessive deposits have been
allowed to accumulate on the heating element,
or (3) there is evidence of general abuse such
as animals chewing on the cord. This warranty
does not cover incidental or consequential
damage resulting from either a defect in parts,
materials, or operation failure. Some states
do not allow the exclusion or limitation of the
above damages so the above limitation may
not apply to you. No agent, employee, or
representative of Miller Manufacturing has any
authority to bind Miller Manufacturing to any
affirmation, representation or warranty directed
towards any products bearing the API name,
except as stated herein. This warranty gives you
specific legal rights--you may also have other
rights which vary from state to state.
MAINTENANCE
Do not allow lime or other impurities in the
water to build up on the heating element. The
frequency of cleaning depends directly upon
the composition of your water supply. The unit
is coated for easy cleaning. However, you may
wish to use lime-removing cleaners that can be
obtained at any farm or hardware store. Use a
soft brush for cleaning.
INSTRUCTIONS FOR THE
LOCKNDRY® CORDSET
- Plugs into any normal 3-prong outlet
- Mates with LOCKNDRY® plugs to form a
water-resistant seal
- Keeps connection from separating during use
- Features a second, locking nut for a secure
connection
INSTRUCTIONS
(1) Insert the plug
into the receptacle
just as you would a
normal extension
cord making sure
the plug is fully
inserted.
(2) Slide the large
nut forward
to engage the
threads on the
plug.
(3) Rotate the nut
to tighten the
plug against the
receptacle.
(4) Slide the
second, thinner,
red nut forward
to engage the
threads.
(5) Rotate the red
nut snugly against
the larger nut.
UTILITY/BUCKET/BIRD BATH/WATERER DE-ICERS
Item # W250, # W500, # DT250, # DT500 and # BDT250
304152