background image

7

6. Connect case leads to motherboard:

6.1 Locate the top panel leads. There is 
      also a USB lead for the front panel. 
      Your motherboard documentation 
      will provide schematics. The triang-
      ular markings      on the leads indi-
      cate positive wires. 

6.2 

Locate front panel leads and case 

      speaker. Again, refer to your 
      motherboard’s documentation 
      for placement schematics.

(For power supply version only.)

5.3 Place the probe labeled ‘HDD’ to the 
      hard-drive’s surface. Use thermal 
      tape for best results. 

Note: You may also leave a sensor loose in the chassis in order to monitor 
the ambient system temperature. 

DO NOT

 place the sensor directly on the 

CPU as it will damage the sensor. 

5.4 Plug the 4-pin connector belonging 
      to the LCD into the power supply to
      monitor system temperatures.

8

7.2 ATX 12V 4/8 Pin  connector X 1

7.5 PCI-Express connector X 2

7.6 Floppy drive connector X 2

7.3 Peripheral connector X 8

7.1 ATX 20/24 Pin connector X 1

7.4 SATA drive connector X 4

Connect PC components to the required power connector 
for each device type.

6

4.4 Connect both fan controller ‘INPUT’s 
      to any available 4-pin power supply 
      connectors. Control air flow using the 
      respective knob on front of the case.
      

4.3 Select those to be used as intake fans 
      and connect male to female ends. The 
      remaining male end is connected to the 
      ‘OUTPUT’ connector of the ‘cool air in’ 
      fan controller. Repeat the steps for 
      exhaust fans using the ‘hot air out’ line.

5. Temperature probe setup:

5.2 Place the probe labeled ‘CPU’ to any 
      ‘fin’ on the CPU’s heatsink and tape 
      in place. Thermal tape should be 
      used for best results.

5.1 Locate the two device temperature 
      probes

4

3.2 From the outside rear of the case,
      push PCI slot cover(s) toward the 
      inside of the chassis.

3.1 First, remove PCI slot covers. Lift 
      the ‘latch’, and open.

2.5 Align rails with hard drive bay 
      and insert.

3. Install PCI components:  

2

1.3 

If your motherboard included an 

      IO shield, you must remove the 
      X-Jupiter's IO shield. Use thumbs 
      or other object to push shield in-
      ward (cover area with a cloth to 
      avoid injury from metal edges!). 

1.5 Put brass standoffs in place. Align 
      motherboard with standoffs and 
      mount to case. This ATX mother-
      board (12”x8.3”) only used notch-
      es A1-A6. M8 was also used since 
      it lined up.

      

1.4 Refer to the motherboard holes 
      index for standoff placement for 
      your motherboard type. A full 
      ATX (12”x9.6”) board will use  
      notches A1-A9. Some mother-
      boards may not use all notches. 
      Use any notches that line up 
      with your motherboard.

NOTE: Touch an unpainted metal 
section of the chassis to discharge 
static electricity before handling PC 
components. An anti-static wrist 
strap should also be worn to further 
minimize the possibility of damage.

3

2.1 To install an optical or floppy drive, 
      remove the drive cover by placing 
      an index finger into either inlet and 
      pulling outward.

2.4 For hard-disk drives, find the 
      mounting rails labeled ‘HDD’ 
      Attach rails to both sides of 
      the drive.

2.2 For 5 1/4” drives, find the mounting 
      rails labeled ODD (optical disk drive). 
      Align left and right rails with drive, 
      and attach. For 3 1/2” drives, use the 
      rails labeled FDD (floppy disk drive). 

2.3 Align rails with drive bay and 
      insert.

Screwdriver 

NOT 

required!

1

1. Motherboard installation:

1.1 Remove thumbscrews from the 
      rear of the X-Jupiter.

1.2 P

ush handle forward to release 

      (window version). Open and 
      remove panel. 

NOTE:

 

CPU and memory installation is not covered in this 

manual. Please refer to the components’ documentation 
for instructions.

25cm Fan version

Window version

(Hardware and case keys are provided inside the chassis’ storage compartment.)

1.

 Motherboard installation..................................1

2. 

Install 3½” and 5¼” drives

..............................3

3. 

Install PCI components.................................4

5. 

Temperature probe setup........................6

6.

...........7

 

Connect case leads to motherboard

7. 

.................8

Identify power supply connectors

8. 

Complete the installation............................9

4. 

Fan installation and setup............................5

9. 

USB/1394/Audio cable pin assignments........9

9

9. USB/1394/Audio cable pin assignments:

5

3.3 Read your expansion card’s 
      documentation. Install card 
      into correct slot for your card 
      type (x1, x16, etc.). Once the 
      card is seated firmly, return 
      latch to the initial position.

4.1 In addition to fans included, you 
      may opt to install an 8 or 12cm 
      ‘blowhole’ fan. In the above pic-
      ture, the arrows indicate which 
      holes to use for mounting a 
      12cm fan.
      

4.2 Inside the chassis, mount fan to 
      the underside of ‘blowhole’ area 
      and screw into place. Make sure 
      the top vent is in the ‘Open’ posi-
      tion to allow warm air to escape.

4. Fan installation and setup:

2. 

Install 3½” and 5¼” drives:

7. 

Identify power supply connectors:

        X-Jupiter

       

Finished Appearance.

8. Complete the installation:

8.1 With all components properly installed, gently 
      return side panels to their original positions 
      and replace all screws. Congratulations! You
      have completed assembly of the X-Jupiter Jr.

Summary of Contents for X-Jupiter













Reviews: