APB-DynaSonics ProSpec - 1U4M4S Owner'S Manual Download Page 10

 

 

PROSPEC 1U – MASTER SECTION

 

 

LED Power On Indicator 

 

Illuminates when AC power is applied to the unit and its DC Power supplies are operating properly.  This 
unit is to be powered from a switched AC source of 100 to 240 Volts at 50/60Hz with no manual voltage 
selection required for different operating voltages.  This unit may to be left on at most times and draws 
less than 25 watts.

 

 

MASTER OUTPUTS (Left-Right, Center, Mono) 

 

Left / Right and Mono Level Control

 

This single level knob simultaneously adjusts the Left, Right and Center output levels of the mixer and has 
a control has a range of from cut-off to +10dB of gain above unity.  The use of a single control simplifies 
the  operation  of  the  mixer  be  it  used  in  a  Mono,  Stereo,  or  LCR  installation  as  all  output  levels  remain 
proportional in output level. 

 

Master Output Metering (Left - Right - Center Outputs) 

The post-fader levels of the Mono, Center, Left and Right outputs are displayed on the 3 master meters.  

 

Sum L-R Switch (Illuminated when activated) 

Sums the Left and Right Mix buses to a mono signal while not affecting the Center output of the mixer.  
This allows for separate left and right speakers in an installation to carry they same signals and is a simple 
solution for situations where each left and right speaker location cannot cover near 100% of the audience 
area making a stereo mix ineffective.    

 

 

Left / Right XLR Balanced Output Connectors

 

These three XLR output connectors provide an o4dBu balanced line level output (100 ohm 
symmetrically-balanced) signal for each of the consoles primary outputs.   

Note that when the front panel L-R 

Sum switch is selected, that the sum of Left and Right appears as the same mono signal on both Left and 
Right XLR output connectors. 

 

HEADPHONE MONITOR SYSTEM

 

 

Headphone Level Control 

 

This control adjusts the level being fed to the headphone system.  

 

 

1/4” And 1/8” Headphone Connectors 

A 1/4” and a 1/8” set of headphone connectors are located on the front panel of the console. 

 

 

Center (C) Headphone Monitor Source Switch (Illuminated when selected) 

 

When this switch is selected, it will route a post master level Center signal equally to the left and right 

stereo headphones as a “phantom center” image.  Note: Center and Left-Right monitor switch may be 

selected and monitored simultaneously. 

 

 

Left-Right (L-R) Headphone Monitor Source Switch  (Illuminated when selected)

 

When selected, this switch will route a post master level left-right signal to the left and right stereo 

headphone and monitor level controls.  Note: Left-Right and Center monitor switch may be selected and 

monitored simultaneously. 

 

 

Automatic Solo to Headphones

 

When any input channels Solo switch is selected (as indicated by the channels solo switch being illuminated), the selected 
input channels solo signal will automatically override the default Left-Right and/or Center monitored signal.

 

 

 

 

LINKING SYSTEM

 

 

A multi-pin connector system is provided that allows the ProSpec pre output level mix-buses and Solo 
systems of multiple mixers to be linked together.   Contact APB about made-to-order cables tailored to 
your specific need. 

Summary of Contents for ProSpec - 1U4M4S













Reviews: