background image

 

 

MX46-800N R1.02

 July 01. 2003 AOpen Inc. 

 

Award Plug and Play BIOS Extension v1.0A 

Copyright © 2003, Award Software, Inc. 

 

If you encounter any trouble while booting your system, follow the 
procedures accordingly to resolve the problem. 

Part Number and Serial Number 

The Part Number and Serial number are printed on bar code label. You can find the bar 
code label on the outside packing or on component side of PCB. For example: 

Model name and BIOS version 

Model name and BIOS version can be found on upper left corner of first boot screen 
(POST screen). For example: 

MX46-800N 

is model name of motherboard; 

R1.02

 is BIOS version 

Make sure if the jumper settings for CPU and DRAMs are correct.

 

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

 

The problem was probably caused
by power supply or motherboard
failure. Please contact your reseller
or local distributor for repairing. 

Perhaps your VGA card or monitor
is defective. 

No

 

Yes

No

 

Yes

It is very possible that your keyboard
is defective. 

During system rebooting, press Del to enter BIOS Setup. Choose
“Load Setup Default". 

The problem should be caused by the
IDE cables or HDD itself. 

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Yes

Turn off the power and unplug the AC power cable, then remove all 
of the addon cards and cables, including VGA, IDE, FDD, COM1,
COM2 and Printer. 

Turn on the power, and check if 

the power supply and CPU fan 

work properly.

 

Start

 

Check if there is display.

Press Ctrl, and Alt key at the 

same time, hold them and then 

press Del to see if the   

system reboots.

Turn off the system and 

re-connect the IDE cable. 

Check if the system can 

reboot successfully. 

End

 

No

 

No

 

P/N: 91.88110.201

 is part number, 

S/N: 91949378KN73 

is serial number. 

Part No. 

Serial No. 

Part No. 

Serial No. 

Summary of Contents for MX46-800L









Reviews: