background image

Pin 1 

1. JP14 Clear CMOS

 

2. Installing CPU 

Everything you need to boot this 
motherboard is included in this 
Easy Installation Guide. For more 
information, a complete 

Online 

User's Manual

 can be found in 

the 

Bonus Pack CD Disc

. Thanks 

for the help of saving our earth.

 

 

PART NO: 49.89L01.011 

DOC. NO: AK76D-EG-E0105A

Hard Drive IDE Cable x 1 

80-Wire IDE Cable x 1 

Floppy Drive Cable x 1 

Bonus Pack CD disc x 1 

Norton Anti-Virus CD x 1 

This Easy Installation Guide x 1

 

 

 

1. 

Pull CPU socket lever and up to 90-degree angle. 

2. 

Locate Pin 1 on the socket and look for a black dot or 
cut edge on the CPU upper left. Match Pin 1 and cut 
edge. Then insert CPU into the socket. 

3. 

Press down CPU socket lever to finish CPU installation. 

You can clear CMOS to restore system default setting. To 
clear the CMOS, follow the procedure below. 

 

1. Turn off the system and unplug the AC power. 

2. Remove ATX power cable from connector PWR2. 

3. Locate JP14 and short pins 2-3 for a few seconds. 

4. Return JP14 to its normal setting by shorting pins 1 & pin2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS? 
1. Boot fail because of overclocking… 
2. Forget password… 
3. Troubleshooting…

 

Normal Operation 

(default) 

Clear CMOS 

1

CPU Pin1

CPU socket 

Lever 

Note:  If you do not match the CPU 
socket Pin 1 and CPU cut edge well, 
you may damage the CPU.

 

Summary of Contents for AK76D









Reviews: