anytronics Anyscene 512 Installation And Operation Manual Download Page 11

 

Units 5 & 6 Hillside Industrial Estate 
London Road, Horndean,  
Hampshire, PO8 0BL 
Tel +44 (0)23 9259 9410    
Fax +44(0)23 9259 8723

   

 

Page 11 of 13 

AT1039 Issue 1 

Anyscene 512 Operating 

Instructions 

 

8.  External Scene Control 

 
8.1.  Pre-July 2018 Models 
 
The Anyscene 512 also has the ability to use external isolated closing contacts to cycle 
round memories 1-7 in ascending sequence.  The contacts should be connected to the 
two screw terminals on the back of the Anyscene 512 PCB, and the EXT DIL switch should 
be set to ON.   
 
When the Anyscene 512 is in DMX output mode (and not when in auto cycle mode), the 
next scene from the 1-7 scene cycle will be selected on each contact closure.  To facilitate 
‘debouncing’ of contact closure, contact closing inputs which occur less than two seconds 
after the previous contact closure will be ignored. 
 
As with the auto cycle mode, if the power is disconnected during this step cycling, when 
the power is restored the cycle will be restarted from whichever scene was first in the cycle.  
 
Whilst in step cycle mode, whichever scene is active, it can be overridden by pressing one 
of the scene recall buttons.  The next contact closure will cause the Anyscene 512 to step 
on  to  the  next  scene  after  this  manually  recalled  scene.    The  remote  contacts  can  be 
disabled by switching the EXT DIL switch to OFF. 
 
When in auto cycle or standby/receive modes, all contact closures are ignored. 
 
 

 

 

Summary of Contents for Anyscene 512














Reviews: