background image

4

 HOW TO USE YOUR RADIO 

Manual Squelch 

11 

Turn the SQUELCH knob clockwise to the exact point where all 

background noise disappears. Please note that this control is fine 

regulation, if you set it to the maximum (fully clockwise), the radio can 

only receive the strongest signal.

Volume switch

21 

a) To turn the radio on, turn the VOLUME knob clockwise. 
b) To increase the sound level, turn the knob further clockwise. 

FUN key

31 

a) Choose band

Press and hold it for over 2 seconds to enter band selection, turn the 

channel knob to choose a band, press FUN again to exit, the radio 

will work on selected band.  

The frequency and channel information in band A to band L, VFO (1 

channel), MEM (8 channels) total 12 bands can be programmed by 

software.  The frequency in band E, UK, PL can not be programmed, 

but the channel information can be changed by software.

Factory Defaulted with only E, UK band, add other bands by software 

if need.

b) Combined Functions

Press FUN, the LCD display “FUNC”, when “FUNC” disappear, press 

ASQ, TST, SC, A/F, MEM, DW, PRG key to enter the function printed 

below the buttons.

ASQ key 

41 

a)  ASQ:

 Press ASQ, The LCD displays “ASQ”, the ASQ function is 

on; press it again to turn off ASQ.

Note: 

ASQ will automatically turn off if the TSQ function turned on.

b)BEP: 

Press  FUN,  the  LCD  display  “FUNC”,  when  “FUNC” 

disappear, press ASQ, the LCD displays “BP”, the key beep function 

is on, press it again to turn off BEP function.

TSQ key

51 

a) TSQ: 

CTCSS and DCS code

Press TSQ, The LCD will display “CTC or DCS”, the CTCSS or DCS 

function is on; press it again to turn off the function.

Note1:

 This function is available only when you installed optional CTC board.

Note2:

 when you choose RXC or TXC off, this function is not valid.

Note3:

 When the CTCSS or DCS is on, the speaker will boot only when it 

receive corresponding CTCSS or DCS code.

Note4:

 When the CTCSS or DCS is on, the RB function will turn off.

b)TOT

 (Timer Out Timer)

Press FUN, the LCD displays “FUNC”, when “FUNC” disappear, press 

TSQ, the LCD displays “XXX  S”,  you can adjust the TX limit time by 

the channel knob, press any other key to exit, or wait for 5 seconds , the 

radio will store the setup and exit.

When the continuous TX time is over the TOT limit, the radio will stop TX.

TOT Optional

15-600 seconds, step 15seconds, default: 180Seconds

SC key

61 

SC 

(Scan function)

Press SC, The LCD displays “SC” and flashes, the radio start scan 

function, turn the channel knob to select the scan mode, press any key 

to exit scan.

Note:

 the scan only on pre-stored channels in present BAND or MEM.

SKP

 (Scan Skip function)

Press FUNC, the LCD display “FUNC”, when “FUNC” disappear, press 

SC, the present channel will delete from the scan list. The scan will skip 

this channel.  Press the key again to add present channel to scan list.

A/F key

71 

A/F

 (AM/FM switch)

Press it to switch between AM and FM mode, the LCD will display AM 

or FM.

HI 

(High low power function)

Summary of Contents for AT-5289














Reviews: