background image

B. List of Lock Accessories

 

Keyhole 

Cover 

Screw (4 PCS) 

Front panel 

Assembly 

4 PCS AA 

Batteries 

Silica gel 

backing plate 

Rear panel 

assembly 

Lock body 

Screw (2PCS) 

Back Lining 

Plate 

10 

Key (2PCS)

 

  Confirm the door information before installation 

1. Installation Requirements

 

This  fingerprint  lock  is  not  configured  with  a  handle,  and  the  user  can  install  it  on  the  door  as  desired.  The 

fingerprint lock is applicable to doors of 35­50 mm in thickness.

 

2.

Make sure of the door opening directions and lock body directions

 

(1).

 Make  sure  of  the  door  opening  directions. The lock  body's  outside and inside  can't  be  set  contrary.  Assume 

you  are  standing  outside  and  facing  a  door  and  then  there  are  four  door  opening  directions:  Left  inward,  left 

outward,  right  inward  and  right  outward.  Left  inward/outward  means  the  door  swings  inward/outward  with 

hinges  on  the  left;  right  inward/outward  means  the  door  swings  inward/outward  with  hinges  on  the  right,  as 

shown in the following

Figure 1

:

 

(2).

  Make  sure  of  the  lock  body  directions.  According  to  the  door  opening  directions  to  make  sure  of  the  lock 

body directions, shown as the following

Figure 2

:

 

  Reference Tools for Installing the Door Lock 

1 Hammer 

2 Screwdriver 

3 Chisel for wood working 

4 Angle square 

Percussion drill 

6 Hole saw 

7 Polisher 

8 Rivet gun 

9 Carpenter's pencil 

10 Pliers

 

. Quick Reference 

 

A. Quick reference for Installation Guide 

Ø

 

Confirm  the  door  information  before  installation

,  please  see 

.  Confirm  the  door  information  before 

installation

; 

Ø

 

Install Lock Body

, please see 

. Install Lock Body

; 

Ø

 

Confirm the length of Locking Bar

, please see 

. Confirm the length of Locking Bar

; 

Ø

 

Install the Front panel Assembly

, please see 

. Install the Front panel Assembly

; 

Ø

 

Install Batteries

, please see 

. Install the Batteries

; 

Ø

 

Install the Rear panel Assembly

, please see 

. Install the Rear panel Assembly

; 

Ø

 

Use Instruction

, please see 

. Use Instructions

; 

Ø

 

The Basic Operation

, please see

. The Basic Operation

; 

Ø

 

Routine Maintenance

, please see 

. Routine Maintenance

.

 

BL100 Installation Guide

 

Version:  V1.0 

Date:  2012.3.16 

­

1

­ 

­

2

­

Summary of Contents for bl100








Reviews: