Anvil VRX1200/330, Manual

Page: 3 / 8

1
UK
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any
repairs if required. Do not remove any components or service panels on
this product.
• Consult Local and National Standards to comply with the following:
• Health and Safety at Work Legislation
• BS EN Codes of Practice
• Fire Precautions
• IEE Wiring Regulations
• Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use the appliance outside.
• DO NOT use this appliance to store medical supplies.
• Always carry, store and handle the appliance in a vertical position and
move by holding the base of the appliance.
• Always switch off and disconnect the power supply to the unit before
cleaning.
• Keep all packaging away from children. Dispose of the packaging in
accordance with the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a RWA agent or
a recommended qualified technician in order to avoid a hazard.
Product Description
VRX1200/330- 5 x ¼ Container Refrigerated Counter Top/Servery Prep
VRX1500/330- 7 x ¼ Container Refrigerated Counter Top/Servery Prep
VRX1800/330- 9 x ¼ Container Refrigerated Counter Top/Servery Prep
VRX2000/330- 10 x ¼ Container Refrigerated Counter Top/Servery Prep
Introduction
Please take a few moments to carefully read through this manual. Correct
maintenance and operation of this machine will provide the best possible
performance from your RWA product.
Pack Contents
The following is included:
RWA prides itself on quality and serv ice, ensuring that at the time of
packaging the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your RWA
dealer immediately.
Installation
1. Remove the appliance from the packaging. Make sure that all protective
plastic film and coatings are thoroughly removed from all surfaces.
2. Maintain a distance of 20cm (7 inches) between the unit and walls or
other objects for ventilation. Increase this distance if the obstacle is a
heat source.
3. Set the brakes on the castors to keep the appliance in position.
Fit Glass Panels
1. Screw the collars to the rim of the appliance.
2. Slot the two side panels into the collars, with the holes in the glass at
the top.
3. Screw a grub screw into each collar to secure the panels.
4. Slot the rear panel into the collars, with the holes in the glass at the top.
5. Screw a grub screw into each collar to secure the panel.
6. Slot the plastic plugs into each of the holes.
7. Screw the brackets to the inside of each pane using the bolt assemblies.
8. Place the top panel onto the brackets, ensuring all holes line up.
9. Insert the plugs and attach the top panel to the brackets with the bolt
assemblies (see below) .
Operation
Storing Food
To get the best results from your RWA appliance, follow these instructions:
•
Only store foodstuffs in the appliance when it has reached the correct
operating temperature.
• Do not obstruct the fans inside the appliance.
Turn On
1. Ensure the power switch is set to [O] and turn on at the socket.
2. Switch on the Power [I]. The current temperature within the appliance
is displayed.
Note: If the unit has been stored in a non-vertical position,
stand it in an upright position for approximately 12 hours
before operation.
• RWA Refrigerator or Freezer
• Top glass panel
• Rear glass panel
• Side glass panels x 2
• Instruction manual
• Collars x 6
• Brackets x 7
• Grub screws x 7
• Screws x 12
• Plugs x 14
• Gastranorm adaptor bar
• Adjustable feet x 4
Note: Before using the appliance for the first time, clean the
internal cabinet and shelves with soapy water.
Note: Ensure the hole in the collar for the grub screw faces
inwards.
Note: Ensure the screw hole furthest from the edge of the
panel goes to the back of the appliance.
Note: Ensure the soft end of the grub screw is the end making
contact with the glass.
Note: Ensure the short end of the bolt assembly is on the
outside of the panels.