SE-4200/4400 WATER FILTRATION SYSTEM
11
P/N 1010852 Rev. C 04/06
OPERATION (continued)
Programming
1. Once the system is connected to a power source,
the unit displays the following messages in the
table below in order:
Message
Description
ANTUNES FILTRATION
Rev. 00.00.00
Shows the software and
hardware revision informa-
tion.
ver- BASIC ON:lcd ON
units- US:audio ON
Indicates the system hard-
ware setup.
BORE AIR RELEASE
00:05 mm:ss
Indicates the unit is filling
filters with water.
STOP MODE
00/00/00 00:00:00 AM
Indicates the controller is
performing internal tests to
verify correct filter operation.
FILTER MODE
00/00/00 00:00:00 AM
Indicates the unit is in
FILTER MODE.
After the system displays the FILTER MODE message,
proceed to the next step.
NOTE: Only a few items need to be programmed
to allow for the proper operation of the system.
Default values in the system programming are set
to automatically flush the filter cartridges for 1 min-
ute every hour. Default values should be sufficient
for most locations’ filtration needs.
NOTE: To skip a value, accept a default value, or to
save a changed value, you MUST press the Enter
button to save the entry and proceed to the next
option. If you make a mistake, press the Menu but-
ton to go back to the previous display.
SET DATE/TIME MODE
NOTE: The Date and Time must be set in order for
proper system operation.
1. If the system does not already display the
SET
DATE/TIME
message, from the FILTER MODE,
press the Stop button. The system enters STOP
MODE and displays
STOP MODE
on the display.
2. Press the Menu button.
3. Using the Up and Down arrow buttons, scroll from
SET PASSWORD
to
SET DATE/TIME
and press
the Enter button.
4. The system displays the
SET DATE
message.
Using the Up and Down arrow buttons, enter the
correct date in mm/dd/yy format. After each entry,
press the Enter button. For example, for June, set
the month as 06 and then press the Enter button.
Set the date and year in this same manner.
5 The system then displays the
SET TIME
message.
Using the Up and Down arrow buttons, enter the
correct hour in hh format and press the Enter but-
ton. Then, enter the correct minutes in mm format
and press the Enter button. Finally, select AM or
PM and press the Enter button.
6. After setting the date and time, the system dis-
plays the
SET DATE/TIME
message. If you need
to make a correction to your settings, you can
press the Enter button and make any changes. If
the settings are correct, press the Menu button to
return to the STOP MODE function. The correct
date and time should be displayed.
7. Press the Run button to return to the FILTER
MODE function.
SET FILL FUNCTION MODE (BORE AIR RELEASE)
1. From the
FILTER MODE
display, press the Stop
button. The system displays the
STOP MODE
message.
2. Press the Menu button.
3. Using the Up and Down arrow buttons, scroll from
SET PASSWORD
to
SET FILL FUNCTION
. Press
the Enter button.
4. The system displays the
BORE AIR RELEASE
message. The default time is displayed as
00:05
seconds, which should be sufficient for
most locations. To change this setting, use the
Up and Down arrow buttons and the Enter key
to make the change. For example, to change the
setting to six, press the Enter button until the cur-
sor is in the fourth position and use the Up/Down
arrow buttons to change the setting to the desired
time.
5. Next, the system displays the
SET FILL
FUNCTION
display. If you need to make a cor-
rection to the Fill Function setting, press the Enter
button to do so. If the setting is correct, Press
the Menu button to save the setting and return to
STOP MODE.
6. Press the Run button to return to FILTER MODE.
