background image

7

P/N 1010807 Rev. E 06/06

VERTICAL CONTACT TOASTER

Figure 2. Installing Bun Chute

Bun Chute

Yellow 

Support 

Rod

Hook Bun Chute over rear 

bottom conveyor cover  

yellow support rod

Figure 1. Toaster and Accessories

Heat 

Shield

Heat 

Shield

Conveyor  

Cover Assy. 

(rear)

Yellow Support 

Rod (front)

Conveyor  

Cover Assy. 

(rear)

Bun Feeder.

Conveyor  

Cover Assy. 

(front)

Unpacking

  1.  Remove unit and all packing materials from ship-

ping carton.

  2.  Open the large box.  It should contain: 

•  Bun Feeder (Figure 1). 

•  Bun Chute (Figure 2) 

•  2 Release Sheets (Figure 1). 

•  Authorized Service Agency Directory 

•  Owner’s Manual

  3.  Remove all packing materials and protective cov-

erings from the unit and parts.

NOTE:  If any parts are missing or damaged, con-

tact Antunes Technical Service IMMEDIATELY at 

1-877-392-7854.

Assembling the Unit

NOTE:  The factory has pre-installed a Release 

Sheet over the Platen (Figure 1).  Verify that it is 

properly in place before proceeding.

  1.  Install the Bun Feeder (Figure 1) and Bun Chute 

(Figure 2).

IMPORTANT: Make sure Heat Shield Assembly 

is properly seated and engages the Conveyor 

Interlock Safety Switch (see Figure 1).  The con-

veyors will not rotate unless the Heat Shield is in 

place and correctly engages the Conveyor Interlock 

Safety Switch.

NOTE: Check the Release Sheet to make sure it 

is not caught in the conveyor.  Additional Release 

Sheets can be obtained through your authorized 

service agency under part no. 7000249 (3 pack) or 

7000250 (10 pack).

INSTALLATION

Release 

Sheet

Yellow 

Support Rod 

(rear)

Bun 

Feeder

Conveyor  

Cover Assy. 

(rear)

Shown without option-

al Roller Tensioners 

and Belt Wraps.

Shown without optional 

Roller Tensioners and 

Belt Wraps.

CAUTION

Failure to use Release Sheets may result in damage 

to the unit and loss of warranty coverage.

Rear 

Conveyor 

Belt Chain

Front Conveyor 

Belt Chain

Platen

Conveyor 

Interlock Switch

Summary of Contents for Roundup VCT-1000

























Reviews: