TECHNOLOGY FURNITURE
®
Trolley Cart
Assembly Instructions
01– Trolley Trunk Assembly (X) ..........
Qty. 1 .................................................
TR18zz/xx.............................................................................. 835-5018-00
TT18zz/xx .............................................................................. 835-5401-00
02– 5” Total Lock Casters
.................
Qty. 2 .................... 150-5081-00
03–
5
/
16
-18 Button Head Screw
.......
Qty. 16 .................. 325-5188-00
04–
5
/
16
-18 X 1” Tube Screws
...........
Qty. 4 .................... 325-5136-00
05– 5” Swivel Lock Casters
..............
Qty. 2 ....................150-5080-00
06– Trolley Trunk Covers ........................
Qty. 2 ................................................
TR18zz/xx..............................................................................225-5753-00
TT18zz/xx ..............................................................................225-4278-00
07– 18.25” Lower Cross Tube ...............
Qty. 1 ......................125-5244-xx
08– Trolley Trunk Assembly (Y) ..........
Qty. 1 .................................................
TR18zz/xx.............................................................................. 835-5019-00
TT18zz/xx .............................................................................. 835-5402-00
09– 12” Upper Cross Tube
...............
Qty. 1 .....................125-5243-00
10– Trolley Cable Wraps .........................
Qty. 2 .....................225-5756-00
11–
1
/
4
-20 Keps Nuts ...............................
Qty. 6 ..................... 325-5202-00
12– 18” Handle ..........................................
Qty. 1 .....................125-5245-00
13– Shelf & Handle Side (X)
............
Qty. 1 .....................225-5754-00
14– 18.5” Wide Trolley Shelf ................
Qty. 1 ..................... 100-6495-00
15– Shelf & Handle Side (Y) .................
Qty. 1 .....................225-5755-00
16–
3
/
4
” Wood Screws ..............................
Qty. 6 ......................325-5106-00
17–
1
/
4
-20 Button Head Screws
......
Qty. 14 ...................325-5210-00
18–
1
/
4
-20 X 2” Handle Screws
........
Qty. 2 .....................325-5034-00
19– Non-Skid Pads
(not shown)
.........
Qty. 8 .....................175-5068-03
Hello!
Thank you for choosing Anthro.
Before beginning assembly of your
Trolley, please take a moment to re-
view the parts listed below to verify
that your shipment is complete.
All fastener quantities shown are the
minimum needed for this assembly.
There may be a few extras provided
which are not required.
Questions?
1-800-325-3841
Step 7a
Install Non-skid Pads on the top of the Trolley Trunk
Covers to cushion the edge of each Trunk Assembly where it
meets the cover. Install pads on the inside face of the cover,
at the edge, about 3.5” below the threaded holes at the top of
the cover.
The following Tools (not shown at right) have
been provided:
Hex Driver
5
/
32
” ............375-5000-00
Hex Key 6mm ...............375-5013-00
3
/
16
” Allen Key ...............375-5028-00
3-way Wrench.............225-5196-03
5/32” Driver Bit ...........375-5003-00
Button Head Screws
Anthro
®
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS!
November 2010, Rev H
1-800-325-3841
Trunk Cover
Step 8
STOP: If yOU PURCHASEd A SwINg OUT mOUSE SHElf REAd
THOSE INSTRUCTIONS BEfORE INSTAllINg THE TOP.
Finally, place the main Trolley Shelf onto the installed
Shelf & Handle Sides, aligning the six holes on the
Shelf with those on the Sides.
Secure the Shelf to the Sides using a total of six
3
/
4
” Wood Screws. Tighten all Screws and Nuts.
Congratulations!
Your assembly is complete!
3
/
4
” Wood Screw
325-5106-00
3
/
4
” wood Screws
into the six Trolley
Shelf holes
Step 7b
STOP: If yOU PURCHASEd A TROllEy
EqUIPmENT SHElf, AddITIONAl wOOd SHElf, OR TROllEy
TRAy REAd THOSE INSTRUCTIONS BEfORE INSTAllINg THE
TRUNk COVERS.
Install the Trolley Trunk Covers by orienting both Covers with
the Trunk Assemblies.
Secure the top and bottom of each Cover using a total of four
Button Head Screws per Cover.
Non-Skid Pad
175-5068-03
Threaded holes
Button Head
Screws
03
05
02
01
08
04
07
06
09
10
11
12
15
16
17
18
13
14
(
1
/
4
-20 X .375”) Button Head Screw
325-5210-00
Component list for
part # TR18zz/xx and TT18zz/xx.
3.5”
Non-Skid Pads
