18
18
EN
R7
- OPERATING INSTRUCTION
5.
Instrument board operation
Layout of instruments.
The positions the instruments are placed in on the board are determined by the customer at the time of order.
Starting the instruments.
• The syringe is always on (see paragraph 5.3.).
• The curing light is turned on with the key when the instrument is withdrawn (see paragraph 5.7.)
• Intraoral camera turn on when the instrument is extracted (see paragraph 5.8.).
• If connected to an external PC, the integrated ZEN-Xi sensor is always operative (see paragraph 5.9.).
• Once picked up, all the instruments are operated with the foot control. (see paragraph 5.2.).
Simultaneous use of the instruments.
A device sees that the instruments cannot be used simultaneously.
The first instrument removed is operative while those removed there after
are deactivated by this device.
This device allows the chuck to be replaced in one instrument while another
is used on the patient.
Putting the instrument board place.
The instrument board can be moved in all directions.
To adjust the height of the board and/or direct it horizontally, simply grasp
the handle (
a
).
NOTE (only for pantograph arm with pneumatic brake):
to
adjust the height of the dentist’s instrument board, you first need to press
the brake release button
.
NOTE model R7 CART / R7 M CART:
o adjust the height of
the dentist’s instrument board, you first need to press the brake release
button
.
Pantograph arm.
There are two types of pantograph arm:
with manual locking (only A5 series)
with pneumatic locking
Adjusting the pantograph arm with manual brake.
Balancing of the pantograph arm is determined at the time of installation.
Any future adjustments can be made using the knob (
b
) found on the
pantograph arm.
Turn clockwise: to increase clutching of the pantograph arm.
Turn counter-clockwise: to decrease clutching of the pantograph arm.
Instrument return arm stopping device (only for CONTINENTAL ver-
sion instrument boards).
If this device is provided, the instrument return arm can be locked in the
instrument extracted position.
When the device is used a click is heard about 2/3 of the total arm travel.
To go back to the original condition, simply move the arm to the end of its
travel (
B
).
Tray holder module for CONTINENTAL version dentist’s instrument board.
The tray holder module (
f
) is made of stainless steel and can easily be
removed from its support.
WARNING!
Maximum permitted load on the tray holder module ( f ): 2 kg distri-
buted.
Tray holder module for INTERNATIONAL version dentist’s instrument board.
The stainless steel tray holder (
e
) can be easily removed from its mount.
The tray holder can be turned both clockwise and counter-clockwise so
that it can be placed in the most convenient position for the operator. The
tray holder arm can be turned both clockwise and counter-clockwise for a
total of 60° passing through 8 set positions.
WARNING!
Maximum permitted load on the tray holder module ( e ): 2 kg distri-
buted.
Summary of Contents for SMART TOUCH R7
