75
5.
REMOTE CONTROL
CUSTOMIZATION
5.1
CODES FOR OTHER BRANDS
The processor remote can control other components – brands and setup instructions are in Appendix B. If the
brand for your component is not listed, try searching for a code as follows:
1. Turn on the component, for example the DVD player.
2. Press a
control mode
key other than MAIN, Z2, or Z3, for example
DVD
.
3. Press and hold
LEARN
until the LED flashes twice then press
9
,
9
,
1
.
4. Press
0
for cable converters, satellite receivers, or video accessories,
1
for TVs,
2
for DVD players
or VCRs, or
3
for CD players or audio amps/tuners.
5. Aim the remote towards the player and press
POWER
(or Play). If the player does not respond, press
CH+
to try the next code. If the player responds, press
LEARN
to lock the code. Codes are sent in
order of popularity. CH
goes to the previous code.
If no code is found, see section 5.2.
6. After finding a code, record it: Press and hold
LEARN
until the LED flashes twice, then press
9
,
9
,
0
,
1
.
Wait 3 seconds and count the number times that the LED flashes. This represents the first digit (for
example, 3 flashes = 3, no flash = 0) – write this down. Next, press
2
for the second digit,
3
for the
third digit,
4
for the fourth digit,
5
for the fifth digit and write the number of flashes each time.
5.2
LEARNING COMMANDS
Commands from almost any other infra-red remote control can be captured by the processor remote control.
The factory command is still available by pressing LEARN before pressing the taught key.
If the factory command is used more than the learned command, the learned command can be programmed
in Layer2 instead. In this case, the learned command is sent by pressing LEARN before pressing the key.
Before teaching a key note the following:
• Control mode keys and LEARN can not be taught. These keys never send IR commands.
• A multiple key sequence (for example Rec+Pause or Rec+Play) can not be taught to one key.
• A high level of ambient light, light from displays, and exposed fans could interfere with learning.
To teach a key:
1. Point the source and processor remotes at each other, holding them 2 inches apart.
2. Press and hold
LEARN
until the LED flashes twice then press
9
,
7
,
5
. One long blink indicates low
battery or faulty memory – the remote will not go into learn mode under these conditions.
3. Press the desired
control mode
key.
4. Press the
key to be taught
, or to program the command into Layer2 press
LEARN
(don’t hold) then
press the
key to be taught
.
5. The LED flashes rapidly. Within 4 seconds, press and hold the
teaching key on the source remote
until the LED flashes twice. One long blink means bad capture (try again), memory full (delete
another command), or unlearnable code.
6. Repeat steps 3-5 or 4-5 as often as desired until memory is full.
7. To exit, press and hold
LEARN
until the LED flashes twice or wait 10 seconds.
Deleting learned commands:
1. Press and hold
LEARN
until the LED flashes twice, then press
9
,
7
,
6
.
2. To delete a learned command from one key, press the
control mode
key, then the
key to be deleted
twice. To delete all learned commands in the control mode, press the
control mode
key twice.
Summary of Contents for Statement D2
Page 1: ...STATEMENT D2 OPERATING MANUAL UPDATES www anthemAV com S O F T W A R E V E R S I O N 1 3 x...
Page 8: ......
Page 87: ...79...
Page 100: ...THE BIG PICTURE FRONT PANEL...
