ANTAIRA LNP-201AG-T User Manual Download Page 12 | Manualshive

Page: 12 / 20

background image

9

Grounding the PoE Injector

Follow the instructions below to attach the PoE Injector to ground.

When installing the PoE Injector, the ground connection must always

be made first and disconnected last.

1. On the top of the device, locate and remove the dome screw which has

a ground symbol beside it.

2. Attach the ground wire to the screw hole with the dome screw.

ATTENTION

«
...
10
11
12
13
14
...
»

Summary of Contents for LNP-201AG-T





















Reviews:

No comments

Related manuals for LNP-201AG-T

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Xo Pages: 59

Brand: Nemalux Pages: 6

Brand: OBDLink Pages: 2

Brand: M-Audio Pages: 25

Brand: Uchida Yoko Pages: 40

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

HALO miniLUME LA5300

Brand: Cooper Lighting Pages: 2

Brand: Free The Tone Pages: 8

Brand: Land Pride Pages: 72

Brand: Airway Pages: 2

Brand: Crazy Foil Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands