ANTAIRA LNP-1204G-10G-SFP Hardware Manual Download Page 20

Page: 20 / 20

Antaira Technologies - Industrial Ethernet Switches

LNP-1204G-10G-SFP Hardware Manual V1.1

Protection

PoE Power Output

30W max. per PoE port

PoE Power Budget

240W

System Power
Consumption

10.7W

Environment Limits

Operating
Temperature

-40°C to 65°C

Storage Temperature

-40°C to 85°C

Ambient Relative
Humidity

5% to 95%, (non-condensing)

Regulatory

Approvals

EMI

FCC Part 15 Subpart B Class A,
CE EN55032/EN61000-6-4 Class A

EMS

CE EN55035/EN61000-6-2 Class A,
IEC61000-4-2,3,4,5,6,8

Free Fall

IEC60068-2-32

Shock

IEC60068-2-27

Vibration

IEC60068-2-6

Green

RoHS Compliant

Certifications

FCC, CE, UL 61010-1, 61010-2-201

Warranty

5 Years

Table 5.1 - LNP-1204G-10G-SFP Technical Specifications

Antaira Customer Service and Support

(Antaira US Headquarter) + 844-268-2472

(Antaira Europe Office) + 48-22-862-88-81

(Antaira Asia Office) + 886-2-2218-9733

Please report any problems to Antaira:

Any changes to this material will be announced on the Antaira website.

Summary of Contents for LNP-1204G-10G-SFP





















Search results

Summary of Contents for LNP-1204G-10G-SFP

Reviews:

Related manuals for LNP-1204G-10G-SFP

Brands by name

Popular brands

ANTAIRA LNP-1204G-10G-SFP, Hardware Manual

Search results

Summary of Contents for LNP-1204G-10G-SFP

Reviews:

Related manuals for LNP-1204G-10G-SFP

Brands by name

Popular brands