ANTAIRA LNP-1002C-SFP User Manual Download Page 6 | Manualshive

Page: 6 / 24

background image

Antaira Technologies - Industrial Ethernet Switches

LNP-1002C-SFP Series User Manual V1.2

2

1.2 Package Contents



1 - LNP-1002C-SFP (T): 10-Port industrial PoE+ unmanaged Ethernet switch, with

8*10/100Tx (30W/Port), 2*Gigabit combo ports (2*10/100/1000Tx RJ45, and 2*
100/1000 SFP Slots)



1 - User manual



1 - Product CD



2 - Wall mounting brackets and screws



1 - DC cable –18 AWG & DC jack 5.5x2.1mm

1.3 Safety Precaution

Attention:

If the DC voltage is supplied by an external circuit, please use a protection

device on the power supply input. The industrial Ethernet switch’s hardware

specs, ports, cabling information, and wiring installation will be described

within this user manual.

«
...
4
5
6
7
8
...
»

Summary of Contents for LNP-1002C-SFP

























Reviews:

No comments

Related manuals for LNP-1002C-SFP

Brand: Hama Pages: 5

SuperStack 3 4900

Brand: 3Com Pages: 2

Brand: Aastra Pages: 12

Brand: Aastra Pages: 2

Brand: Kathrein Pages: 41

Aeotec Micro Smart Energy Switch G2

Brand: Aeon Labs Pages: 11

Brand: Witura Pages: 21

Brand: Lindy Pages: 70

Brand: SMC Networks Pages: 43

3C63100-AC-C - PathBuilder S600...

Brand: 3Com Pages: 232

ETHERLINE ACCESS U04TP01T

Brand: LAPP Pages: 16

EOC Master CD7944N

Brand: Data Pages: 18

Brand: B&B Electronics Pages: 22

3C17205 - SuperStack 3 Switch 4400 PWR

Brand: 3Com Pages: 90

BNI EIP-950-000-Z009

Brand: Balluff Pages: 12

Brand: Key Digital Pages: 20

LMX-1002G-SFP Series

Brand: ANTAIRA Pages: 22

Brand: Minicom Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands