Antaira Technologies
IMP-C1000-SFP Series
10/100/1000TX to 100/1000FX Compact Industrial Gigabit
Media Converter with SFP Slot and PoE Injector
Quick Installation Guide
Version 1.1
Feb 2020
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
Package Check List
The package contains the following items:
Quick Installation Guide
1 * IMP-C1000-SFP Industrial Gigabit Media Converter
1 * Wall mounting bracket set with screws
1 * DC cable
–18 AWG & DC jack 5.5x2.1mm
Front Panel Layout
Top Panel View
IMP-C1000-SFP series top panel is equipped with one 4-pin
removal terminal block connector for dual DC power inputs
(48~55VDC).
Product Overview
System Interface/Performance
RJ-45 port support the auto MDI/MDI-X function
Ethernet RJ-45 port connectivity 1*10/100/1000TX (w/PSE:
30W/port)
Fiber connectivity with 1*100/1000FX SFP slot
Store-and-forward switching architecture
Jumbo frame support up to 10k
Power line EFT protection: 2,000VDC; Ethernet ESD
protection: 6,000VDC
Power Input& Connection
DC 48~55VDC redundant power, with a 4-pin removal
terminal block
It is recommended to using UL listed Industrial Power
Supply
Operating Temperature
Standard operating temperature model: -10°C ~ 70°C
Extended operating temperature model (
–T): -40°C ~ 80°C
Case/Installation
IP-30 protection
DIN-Rail and wall mount design
Safety Precaution
If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
LED Indicators
LED
Color
Description
Power
Green
On
Power input 1 or 2 is active
Off
Power input 1 and 2 are inactive
Link Activity
(SFP Port)
Green
On
Linked to network at 100/1000Mbps
Flashing
Networking is active
Off
Not connected to network
RJ45 Port
(Upper LED)
Green
On
Linked to network at 1000Mbps
Flashing
Networking is active
Off
Not connected to network
RJ45 Port
(Lower LED)
Green
On
Linked to network at 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
PoE Status
Green
On
The port is supplying power to the
powered-device
Off
No powered-device attached
or power supplying fails
Quick Installation
DIP-Switching Setting
There are 2
sets of DIP
‐
switches on the front panel that are
responsible for the settings of the SFP (Link Fault Pass) function
and the SFP transmission rate.
DIP 1
DIP 2
Description
ON
ON
LFP Enable and Set SFP to 100Mbps
ON
OFF
LFP Enable and Set SFP to 1000Mbps
OFF
ON
LFP Disable and Set SFP to 100Mbps
OFF
OFF
LFP Disable and Set SFP to 1000Mbps
Note: After any DIP switch changes have been made, it is
required to power cycle the unit for the changes to take
effect
Ethernet RJ45 Port (Auto MDI/MDIX)
RJ-45 port is auto-sensing for 10Base-T, 100Base-TX or
1000Base-TX devices connections. Please follow the wiring pin
assignment table below for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
Pins
T568A Color
T568B Color
10/100
Base-T(X)
1000
Base-T
PoE
1
White/Green
White/Orange
Rx+
TP0+
DC+
2
Green
Orange
Rx-
TP0-
DC+
3
White/Orange
White/Green
Tx+
TP1+
DC-
4
Blue
Blue
unused
TP2+
5
White/Blue
White/Blue
unused
TP2-
6
Orange
Green
Tx-
TP1-
DC-
7
White/Brown
White/Brown
unused
TP3+
8
Brown
Brown
unused
TP3-
4-Pin Removal Terminal Block (Power Input)
Fiber Port
– 100/1000FX
Grounding Screw
LED for PWR
DIP switches for LFP setting
LED for RJ45 10/100TX network speed status
LED for RJ45 1000TX network speed status
10/100/1000TX RJ45 port
LED for network fiber connection
LED for PoE
