Antaira Technologies
FCN-3112 Series
1010/100/1000TX to 1000SX SNMP Managed Media Converter
Quick Installation Guide
Version 1.0
(October 2018)
Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com
Package Check List
The package contains the following items:
⚫
1
– Quick installation guide
⚫
1
– FCN-3112 Series media converter
⚫
1
– 5 volt power supply
⚫
1
– CD
Front Panel Layout
Figure 1. Media Converter Dual-Fiber Front Panel
Figure 2. Media Converter Single-Fiber & SFP Front Panel
Back Panel View
Product Overview
The media converter series is designed to meet the increasing
needs for Gigabit network deployment and is able to extend a
copper-based Gigabit network via fiber cable to a maximum
distance of up to 80KM.
The media converter series is fully compliant with IEEE 802.3,
802.3u, 802.3ab & 802.3z standards. It can be installed into a
Converter RACK. The installation and operation procedures are
simple and straightforward. Operation status can be locally
monitored through a set of diagnostic LED indicators located in
the front panel.
-10/100/1000Base-T to 1000BASE-X Converter
-Standard: IEEE 802.3, 802.3u, 802.3ab, and 802.3z
-Interface: 1 x RJ-45 LAN connector
1 x SC connector or 1 x SFP slot
1 x Diag. button
-Auto-Negotiation in TX port
-MDI/MDIX Auto-Crossover supported
-LED: Power, FDX, Status, Speed, FO Link/Act, TX Link/Act
-Plug-and-Play installation
-Support Link Alarm
-Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
-Support Selectable ISP Ethernet Tag Type
-Q-in-Q Double Tag configuration
-Support DHCP Client
-Support SNMP / Web Managed interface
-Support SNMP v1 and v2c
-Support HTTP Firmware Upgrade
-Support Power Down Trap Management
LED Indicators
LED
Color
Description
Power
Green
On
Power is active
Off
Power is inactive
FDX
Green
On
Copper connection is in full duplex
Off
Copper connection is not in full duplex
Status
Amber/Green
Amber
Lit when TP or FO link is down. Blink when
diagnostic testing has failed.
Green
Lit when TP and FO link is up. Blink when
Loopback test is being performed.
Speed
Amber/Green
Amber
Lit when TP works in 1000M.
Green
Lit when TP works in 100M. Not lit when TP works
in 10M or is not linked.
FO (Link/Act)
Amber/Green
Amber
Blink when fiber or copper link is down in Link
Alarm Enabled mode
Green
Lit when fiber cable connection with the remote
device is good. Blink when FO traffic is present
TX (Link Act)
Amber/Green
Amber
Blink when fiber or copper link is down in Link
Alarm enabled mode
Green
Lit when TX cable connection with the remote
device is good. Blink when TP traffic is present
DIP Switch Settings
Pin NO. & Button
Function
Off
On
1
TX Auto-Negotiation
Disable
Enable
2
Manual TX Data Rate 10M/100M
10M
100M
3
Manual TX Data Rate 1000M
10M or 100M
1000M
4
Flow Control
Disable
Enable
5
Fiber Auto-Negotiation
Force
Enable
6
Reserved
Always off!!!
7
Link Alarm
Disable
Enable
8
TP Configuration
From S/W
From DIP
Diag. Button
Press once for Loopback test. Press for 10 seconds to restore factory default
settings.
