background image

2

VNA Master MS202xA MM

4.

Performance Verification

The following tests can be used to verify the performance or operation of the VNA Master.

4.1

Frequency Accuracy

The following test can be used to verify the CW frequency accuracy of the VNA Master. Measurement calibration of the 
VNA is not required for this test.

Equipment Required:

VNA Master External Power Supply, Anritsu Part Number 40-168

Frequency Counter, Anritsu Model MF2412B

RF Coaxial Cable, Anritsu Model 15NN50-1.5C

Procedure:

 1.

Connect the external power supply (Anritsu part number 40-168) to the VNA Master.

 2.

Press the 

On/Off

 key to turn on the VNA Master.

 3.

Press the 

Shift

 key, the 

Preset

 key (1), and then the 

Preset

 soft key to reset the instrument to the default start-

ing conditions.  

 4.

Press the 

Measurement

 key, then press the 

S21 Transmission

 soft key. Verify that the 

Log Magnitude

 soft 

key is selected (there will be a red dot on the key label). If not, select the 

Log Magnitude

 soft key.

 5.

Press the 

Shift

 key, then press the 

Sweep

 (3) key.

 6.

Verify that the 

RF Immunity

 is set to 

Normal

 (the word 

Normal

 will be underlined on the soft key label). If not, 

press the 

RF Immunity

 soft key to set the instrument to 

Normal

.

 7.

Press the 

Freq/Dist 

key, then press the 

Start Freq 

soft key.

 8.

Verify that the Start Frequency is set to 2 GHz. If not, enter 

2

 then press the 

GHz

 soft key to set the Start Fre-

quency to 2 GHz.

 9.

Press the 

Stop Freq

 soft key.

 10. Using the keypad, enter 

2

 and press the 

GHz

 soft key to set the Stop Frequency to 2 GHz.

 11. Connect the RF cable from the VNA Master 

RF Out

 test port to the

 RF Input1

 connector on the Frequency 

Counter.

 12. Turn on the Frequency Counter and press the 

Preset

 key.

 13. Verify that Frequency Counter reading is 2 GHz, ±50 KHz.

4.2

Port Isolation

The following test can be used to verify the transmission test port isolation. Measurement calibration of the VNA Master 
is required for this test.

Equipment Required:

50 Ohm Termination, Anritsu Model 28N50-2

50 Ohm Termination, Anritsu Model 28NF50-2

Open/Short, Anritsu Part Number 22N50

VNA Master External Power Supply, Anritsu Part Number 40-168

RF Coaxial Cable, Anritsu Model 15NN50-1.5C

Procedure:

 1.

Connect the external power supply (Anritsu part number 40-168) to the VNA Master.

 2.

Press the 

On/Off

 key to turn on the VNA Master.

NOTE:  Before continuing, allow a 30-minute warm up for the internal circuitry to stabilize.

Summary of Contents for MS2024A
















Reviews: