background image

   

 
 
 

  

 

 

  

  Fig 1   

                  Fig 2  

 

          Fig 3 

 

 
 
 

 

 
  Fig 4   

                 Fig 5                                      Fig 6 

WATER INLET SCREEN 

The water inlet filter must be inspected regularly, so as to avoid blockage and restriction in the 
water supply to the pump (fig 5). 

USING DETERGENT 

Add detergent to the container. Set the Adjustable Spray Wand at low pressure position. (fig 

6) Trigger gun to spray detergent. 
 

LONG TERM STORAGE 

The machine should be stored in a frost-free environment. 
After long-term storage without operation, it is possible to form scales inside the machine making 
it hard to start again. In such conditions it is recommended to turn off and disconnect the power 
supply and 

rotate the motor by hand several times 

so as to avoid excessive current draw on the 

motor and the power supply. 

 

GUN SAFETY DEVICE 

Whenever you use the high pressure washer, we suggest you grip the in the right position, with 

one hand on the handle and the other on the lance, When you stop the machine it is necessary to 

use the safety lock placed on the gun in order to avoid accidental. 

 
 
 
 

Summary of Contents for APW-VAS-130P













Reviews: