background image

 
WordClock-2 Assembly Guide 4/20/20 Version 1.3 
 
 

 

Page 11

 

 

Warranty Terms and Conditions 

 
This software and hardware product is Copyright (C) 2019 by Mitchell Feig. It is exclusively 
distributed by StocksClocks LLC. All Rights Reserved. StocksClocks warrants that for a period 
of  90  days  following  delivery,  kit  parts  will  (a)  perform  in  accordance  with  published 
specifications, and (b) will be free from defects in materials and workmanship. In the event a kit 
part  does  not  meet  this  warranty,  subject  to  the  conditions  set  forth  in  these  terms  and 
conditions, StocksClocks sole obligation will be, at its election, to repair or replace the kit part 
in question. We may require return of the part for examination and replacement. Replacement 
will  be  completed  at  the  sole  discretion  of  StocksClocks,  after  examining  the  returned  part. 
Correct assembly is the responsibility of the builder. 
 

StocksClocks  MAKES  NO  OTHER  WARRANTIES,  EXPRESS  OR  IMPLIED,  AND  ALL 
IMPLIED  WARRANTIES  OF  MERCHANTABILITY,  NON-INFRINGEMENT,  AND  FITNESS 
FOR  A  PARTICULAR  PURPOSE  ARE  HEREBY  DISCLAIMED.  IN  NO  EVENT  WILL 
Stocksclocks BE LIABLE FOR PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, OR 
FOR  AN  AMOUNT  IN  EXCESS  OF  THE  PURCHASE  PRICE  OF  THE  DEFECTIVE 
Stocksclocks PART OR PRODUCT. 

 

 

Summary of Contents for WordClock-2












Reviews: