9
UNDER CABINET INSTALLATION
For Model No.: RAX2130SQB-1 / RAX2136SQB-1 / RAX2142SQB-1
Preparation before Installation
NOTE: TO AVOID DAMAGE TO YOUR HOOD,
PREVENT DEBRIS FROM ENTERING THE
VENT OPENING.
-
Decide the location of the venting pipe from the
hood to the outside. (Figure 1)
-
A straight, short vent run will allow the hood to
perform more efficiently.
-
Try to avoid as many transitions, elbows, and long
run as possible. This may reduce the performance
of the hood.
-
Temporarily wire the hood to test for proper
operation before installing. If the hood does not
operate, check the circuit breaker or house fuse.
If the hood is still not working, disconnect power
supply and check the continuity of all wire
connections.
-
Peel protective film off the hood (if any).
-
Use duct tape to seal joints between pipe sections.
-
Make sure the cabinet has full access opening for
the hood as shown on Figure 2.
-
Using reference on Page 16 to measure and create
access opening for electrical wires and exhaust
under the cabinet.
Hood Installation
CAUTION:
USE HAND TOOLS ONLY. DO NOT
OVER TIGHTEN SCREWS. IT MAY CAUSE DAMAGE TO
THE HOOD.
CAUTION
: If moving the cooking range is
necessary to install the hood, turn off the power in
an electric range at the main electrical box. SHUT
OFF THE GAS BEFORE MOVING A GAS RANGE.
And use a protective covering to protect cooktop
and/or countertop from damage.
1. Using references on Table 1 and measurements on
page 17 mark the leveling point for hood-mounting
bracket inside the cabinet.
2. Secure two hood mounting screws (provided)
inside the cabinet leaving 1/8” away from the
cabinet as shown on Figure 3.
3. Loosen hood-mounting brackets at the back of the
hood, adjust brackets and tighten screws as shown
in Figure 4.
4. Refer to Figure 5. Align hood-mounting bracket to
the mounting screws inside the cabinet and hook
hood into place. Secure and tighten the mounting
screws.
CAUTION
: MAKE SURE THE HOOD IS
SECURE BEFORE RELEASING.
Figure 1
Figure 2
Figure 3
Figure 4
Summary of Contents for RAX2130SQB-1
