background image

2

1

REMOVAL

#2 Phillips Bit
(provided)

Tools Recommended:

b1 

From the interior of the screen assembly, remove the three screws  

from the 

Sill Adapter

.

b2 

Rotate 

Sill Adapter

 up and pull out of 

Adapter Channel

 

(see Figures 1 & 2)

.

b3 

Save the 

Sill Adapter

 for reinstallation in future step.

SILL

ADAPTER

SILL

ADAPTER

DOOR  

SILL

ADAPTER

CHANNEL

SILL

ADAPTER

DOOR

SILL

Figure 2

Figure 1

SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.

RECOMMENDED TOOLS

Drill

Safety Glasses

Sealant

Screwdrivers

!

!

1/2”

1/2”

1/2”

1”

1 1/2”

2”

1 1/2”

5/8”

5/8”

Screwdriver

#2 Phillips Bit
(provided)

!

!

1/2”

1/2”

1/2”

1”

1 1/2”

2”

1 1/2”

5/8”

5/8”

Work Gloves

DOOR OPENING

HANDLE

DOOR OPENING

HANDLE

SCREEN HOUSING 

SCREEN HOUSING 

a

  From the exterior of the screen assembly, take note of the screen 

assemblies orientation. This is the orientation the screen assembly 

should be in when reinstalled.

a

OR

!

!

1/2”

1/2”

1/2”

1”

1 1/2”

2”

1 1/2”

5/8”

5/8”

!

!

1/2”

1/2”

1/2”

1”

1 1/2”

2”

1 1/2”

5/8”

5/8”

The retractable insect screen is intended for reasonable 

insect control and not the retention of objects, persons, 

or pets within the interior. The retractable insect screen 

will not stop a person from falling through the door.

Follow manufacturers' instructions for hand and power 

tools. Always wear safety glasses. Failure to do so could 

result in injury, product or property damage.

Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough 

strength to lift, carry, and install window and door products. Heavier windows and doors will require mechanical 

assistance. Failure to do so could result in injury, product or property damage.

Metal fasteners and components could corrode when exposed to preservative-treated or fire-retardent treated 

lumber. Use approved fasteners and components to fasten window or door. Failure to do so could cause a failure 

resulting in injury, product or property damage.

Fastener must attach to a structural framing member with a 1" minimum fastener embedment. Failure to do so 

could result in injury, product or property damage.  

DO NOT

 remove screws that attached installation clips or gusset plates to window or door frames. Doing so could 

result in injury, product or property damage.

Metal components of the retractable insect screen may 

become hot when exposed to sunlight.

IMPORTANT 

WARNING

WARNING

WARNING

CAUTION

Major Injury / Death

Product or Property 

Damage

Minor Injury

Procedure and Product 

Information

This is the Safety Alert Symbol used to alert you to 

potential injury hazards. Obey all safety messages that 

follow this symbol to avoid possilbe injury or death.

WARNING

NOTICE

CAUTION

IMPORTANT 

Signal Word and Consequence

COULD 

Result in:

COULD 

Result in:

COULD 

Result in:

Summary of Contents for LuminAire









Reviews: