background image

SYSTEM SETUP

5

GENERAL OPERATION

8

MegaVox Pro Control Panel

1. Set all input level controls to minimum before turning on the

power.

2. Plug a microphone into a Mic jack, or an audio source into

the Line-in jack.

3. Turn POWER on, the red LED near the switch will light.  If

the LED flashes or dose not light, charge the battery.

4. Slowly increase the level control adjacent to the input jack

used to desired volume.

NOTE:

Instructions

for wireless

operation can

be found on

page 10.

Charging Indicator

Line In
Controller

Mic/Signal Alert
Controller

Wireless

Receiver 2

Controller

Wireless

Receiver 1

Controller

Line Out Jack

Charger Input

Line In Jack

Speaker Out
Jack

Mic In Jack

Wireless

Receiver 1

Wireless
Receiver 2

Power Switch

Power/Battery Indicator

Signal Alert Button

NOTE:  

All in/out line

connections

must be made

with shielded

cable to avoid
hum, buzzing,

or radio

interference.

MEGA-6000U2

Back Panel

MEGA-6000U1

Back Panel

Wireless Receiver/

Mic Controller

Mic Controller

MEGA-6000
Back Panel

Daisy-Chaining

By using the Line Output method described above you can connect
up to six powered MegaVox Pro PA Systems together expanding
your coverage area.

Daisy-Chain Setup

To connect your MegaVox Pro units, use a shielded cable with 1/4”
phone plugs on each end (EX-50PP).

1. Turn the power switch off and turn the volume to maximum

on each MegaVox Pro.

2. Connect the Line Out on the primary (first) MegaVox Pro to

the Line In on the next MegaVox Pro.

3. Continue connecting your powered MegaVox Pro systems

Line Out to Line In to complete your chain.

4. Power on the speakers in order, primary unit first.  This will

avoid speaker popping which can cause damage.

5. Use the volume control on the primary unit to set the volume

for the entire chain.

6. Power off speakers in reverse order, primary unit last.  This

will avoid speaker popping which can cause damage.

NOTE:

Auditoriums

or outside

areas with

large exposed

walls or

patios may

create multiple

reflections of

the original

sound.

Altering the

PA system

position will

minimize the

sound

reflections.

MegaVox Pro

Daisy-Chain

Secondary
Powered
MegaVox Pro

Line Out - to - Line In Connection

Primary

Powered

MegaVox Pro

Summary of Contents for MegaVox PRO MEGA-6000









Reviews: