manualshive.com logo in svg

Anatomic SITT Zitzi Delfi Pro, User Manual

Share
Download
Anatomic SITT Zitzi Delfi Pro User Manual Download Page 3

3

User manual  Zitzi Delfi Pro

www.anatomicsitt.com  | +46 11 16 18 00

Introduction 

In order to use the Zitzi Delfi PRO in its full extent, it is important that you read this 
manual. This applies to everyone close to the user.
The product is intended for users with seating problems and fits many different 
kinds of diagnoses. Adaptation/fitting of Zitzi Delfi Pro must be done by a 
medically qualified person.
If you need additional information, please contact Anatomic SITT AB.

Field of application

The product is only intended for use as a seating system together with chassis 
produced by Anatomic SITT AB.
If other uses are desired, please contact Anatomic SITT AB.

Correspondence

Zitzi Delfi Pro and its accessories are CE marked products. A unique serial number 
is located on a label placed under the activation housing. This serial number should 
be quoted in any correspondence regarding the product.

Check the checkbox if the product 
is CUSTOMIZED. 

The CE Mark is no longer valid and 
should be removed.

Place of label

This product is manufactured by Anatomic SITT AB 
Postal address

  

Anatomic SITT AB, Box 6137, SE-600 06 Norrköping

Street address

  

Anatomic SITT AB, Terminalgatan 1, SE-603 61 Norrköping

Phone

  

+46 11-161800 

Fax

  

+46 11-162005 

Email

  

[email protected] 

Webb

  

anatomicsitt.com 

Instructions movies

   youtube.com/anatomicsitt

Follow us on

  

facebook.com/anatomicsitt

Safety precautions

Crash tested

Zitzi Delfi Pro is crash tested and approved according to ISO 16840-4. 

Summary of Contents for Zitzi Delfi Pro

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands