Analytic Systems PWS1000 Installation & Operation Manual Download Page 3

3

IMPORTANT & SAFETY INSTRUCTIONS

1.  SAVE THESE INSTRUCTIONS — This manual contains important safety and operating 

instructions for power supply.

2.  Do not expose power supply to rain or snow.
3.  Use of an attachment not recommended or sold by the power supply manufacturer may 

result in a risk of fire, electric shock, or injury to persons.

4.  Do not disassemble power supply; take it to a qualified serviceman when service or 

repair is required.  Incorrect reassembly may result in a risk of electric shock or fire.

5.  To reduce risk of electric shock, unplug power supply from outlet before attempting any 

maintenance or cleaning.  Turning off controls will not reduce this risk.

6.  Never place marine power supply directly above battery; gases from battery will corrode 

and damage power supply.

7.  Never allow battery acid to drip on power supply when reading gravity or filling battery.
8.  O/P CONNECTION PRECAUTIONS

Connect and disconnect DC output connections only after setting the power supply 

switch to the off position.

GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS  — 

The plug must 

be plugged into an outlet that is properly installed and grounded in accordance with al local 

codes and ordinances.

DANGER — 

Never alter AC cord or plug provided — if it will not fit outlet, have proper cord 

installed by a qualified electrician.  Improper connection can result in a risk of an electric 

shock.

Analytic Systems does not recommend the use of the PWS1000 Series Power Supplies in life 

support applications where failure or malfunction of this product can be reasonably expected 

to cause failure of the life support device or to significantly affect its safety or effectiveness.  

Analytic Systems does not recommend the use of any of its products in direct patient care.

Examples of devices considered to be life support devices are neonatal oxygen analyzers, 

nerve stimulators (whether used for anesthesia, pain relief, or other purposes), autotransfu-

sion devices, blood pumps, defibrillators, arrhythmia detectors and alarms, pacemakers, 

hemodialysis systems, peritoneal dialysis systems, neonatal ventilator incubators, ventilators 

for both adults and infants, anesthesia ventilators, and infusion pumps as well as any other 

devices designated as “critical” by the U.S. FDA.

Summary of Contents for PWS1000













Reviews: