manualshive.com logo in svg

Analog Devices SHARC ADSP-214 Series, Hardware Reference Manual, Page: 495 / 1192

Share
Download
Analog Devices SHARC ADSP-214 Series Hardware Reference Manual Download Page 495

ADSP-214xx SHARC Processor Hardware Reference

10-37 

Serial Ports

Companding Limitations (ADSP-2146x)

In multichannel mode there is an option to enable companding for any 
active channel. If the first active channel is NOT the channel 0 and com-
panding is enabled for the first active channel (channel 2), then from the 
second frame onward companding for the first  active channel (channel 2) 
does not occur. In 

Table 10-9

, x = Don’t care 0 = Not Active 1 = Active.

In 

Table 10-9

 channel 0 and 1 are not active and channel 2 is active and 

companding is enabled. In the first frame companding occurs for the first 
active channel (channel 2) but the second frame onward companding for 
the first active channel (channel 2) does not occur. However, for other 
channels, companding occurs correctly.

Packed Mode

A packed mode is available in the SPORT and used for audio codec com-
munications using multiples channels. This mode allows applications to 
send more than the standard 32 bits per channel available through stan-
dard I

2

S mode. Packed mode is implemented using standard multichannel 

mode (and is therefore programmed similarly to multichannel mode). 
Packed mode also supports the maximum of 128 channels as does multi-
channel mode as well as the maximum of (128 x 32) bits per left or right 
channel.

As shown in 

Figure 10-9

, packed waveforms are the same as the wave 

forms used in multichannel mode, except that the frame sync is toggled 

Table 10-9. Companding

Channel  Number

0

1

2

3

4

5

Active Channel Number

0

0

1

x

x

x

Companding Enable

0

0

1

x

x

x

www.BDTIC.com/ADI

Summary of Contents for SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments