background image

EVAL-SSM3582Z User Guide 

UG-934 

 

Rev. 0 | Page 13 of 13 

Qty  Reference Designator  Description 

Manufacturer 

Part Number 

R19 to R25 

Chip resistors, 47.5 kΩ, 1%, 100 mW, thick film, 0603 

Panasonic EC 

ERJ-3EKF4752V 

R27 to R30 

Chip resistors, 0 Ω, 5%, 250 mW, thick film, 1206 

Panasonic EC 

ERJ-8GEY0R00V 

S1 

Switch, dual inline package, 4-poles, sealed SMD 
(half-pitch) 

Omron 

A6H-2102 

S2 

Single-pole double throw, slide switch, PC mount 

E-Switch 

EG1218 

S3 

Dual-pole, dual-throw, slide switch, vertical 

E-Switch 

EG2207 

S4 

Tact switch, 6 mm, gull wing 

Tyco/Alcoswitch 

FSM6JSMA 

36  TP1 to T10, TP12 to T19, 

TP21 to T30, TP32 to T39 

Mini test points, white,1", OD 

Keystone Electronics 

5002 

TP41 

Gold pad only 

Do not install 

Do not install 

U1 

15 Mb/s, fiber optic receiving module 
with shutter 

Toshiba 

TORX147L(FT) 

U2 

High accuracy, ultralow IQ, 500 mA, any capacitor, 
low dropout regulator 

Analog Devices, Inc. 

Not applicable 

U3 

Fixed 5 V output, 20 V Input, 300 mA, low noise, 
CMOS LDO 

Analog Devices, Inc. 

ADP7102ACPZ-5.0 

U4 

High accuracy, ultralow IQ, 500 mA, any capacitor, 
low dropout regulator 

Analog Devices, Inc. 

Not applicable 

U5 

IC 2×, 31.76 W, Class-D amplifier 

SSM3582

40-lead LFCSP 

Analog Devices, Inc. 

SSM3582

 

U6 

192 kHz digital receiver, 28-TSSOP 

Cirrus Logic 

CS8416-CZZ 

U7 

Microprocessor voltage supervisor, logic low, 
RESET output 

Analog Devices, Inc. 

ADM811TARTZ-REEL7 

Y1 

12.288 MHz, fixed SMD oscillator, 3.3 V to 5 V dc 

Cardinal Components 

CPPFX C 7 L T - A7 BR - 
12.288MHz TS 

 
 
 
 

I

2

C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). 

 

 

ESD Caution  
ESD (electrostatic discharge) sensitive device

. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection 

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. 

Legal Terms and Conditions 

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set 

forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have 
read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement.  This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with 

its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-

exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and 

exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer 
shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity 

other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are 

reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the 

Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. 
ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it 

makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with 

applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation 

Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI 
SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 

WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY 

INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, 
LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not 

directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING  LAW. This Agreement shall 

be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state 

or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the 
International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

 

©2016  Analog Devices, Inc. All rights reserved. Trademarks and  
 registered trademarks are the property of their respective owners. 
  

UG14262-0-4/16(0)  

 

Summary of Contents for EVAL-SSM3582Z















Reviews: