background image

UG-1444 

EVAL-ADHV4702-1CPZ 

User Guide 

 

Rev. 0 | Page 2 of 10 

TABLE OF CONTENTS 

Features .............................................................................................. 1

 

Evaluation Kit Contents ................................................................... 1

 

Documents Needed .......................................................................... 1

 

General Description ......................................................................... 1

 

EVAL-ADHV4702-1CPZ Photographs ......................................... 1

 

Revision History ............................................................................... 2

 

Evaluation Board Hardware ............................................................ 3

 

Board Stackup ............................................................................... 3

 

Initial Power-Up ........................................................................... 3

 

Power Supplies and Decoupling ................................................. 3

 

Input and Output .......................................................................... 3

 

Digital Ground (DGND) ............................................................. 3

 

Shutdown Feature (SDN Connector) .........................................4

 

Input Clamping Diodes ................................................................4

 

Input Guard Ring ..........................................................................4

 

Thermal Monitor/Flag (TMP) and Thermal Management .....4

 

Resistor Adjustable Quiescent Current (RADJ) ........................4

 

Evaluation Board Schematics...........................................................5

 

Ordering Information .......................................................................7

 

Bill of Materials ..............................................................................7

 

High Voltage Evaluation Board .......................................................9

 

Warnings, Restrictions, and Disclaimers ...................................9

 

 

REVISION HISTORY 

11/2018—Revision 0: Initial Version 

 

Summary of Contents for EVAL-ADHV4702-1CPZ











Reviews: