manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

ADSP-BF537 Blackfin Processor Hardware Reference

14-9 

 

General-Purpose Ports

The 

PORT_MUX

 register controls the muxing schemes of port F, port G and 

port J.

The function enable register (

PORTF_FER

, 

PORTG_FER

, 

PORTH_FER

) enables 

the peripheral functionality for each individual pin of port x.

Performance/Throughput

The 

PFx

, 

PGx

, and 

PHx

 pins are synchronized to the system clock (

SCLK

). 

When configured as outputs, the GPIOs can transition once every system 
clock cycle.

When configured as inputs, the overall system design should take into 
account the potential latency between the core and system clocks. Changes 
in the state of port pins have a latency of 3 

SCLK

 cycles before being detect-

able by the processor. When configured for level-sensitive interrupt 
generation, there is a minimum latency of 4 

SCLK

 cycles between the time 

the signal is asserted on the pin and the time that program flow is inter-
rupted. When configured for edge-sensitive interrupt generation, an 
additional 

SCLK

 cycle of latency is introduced, giving a total latency of 5 

SCLK

 cycles between the time the edge is asserted and the time that the 

core program flow is interrupted.

Description of Operation

The operation of the general-purpose ports is described in the following 
sections.

Operation

The GPIO pins on port F, port G, and port H can be controlled individu-
ally by the function enable registers (

PORTx_FER

). With a control bit in 

these registers cleared, the peripheral function is fully decoupled from the 
pin. It functions as a GPIO pin only. To drive the pin in GPIO output 

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
ZyXEL Communications ZyAIR B-100 Quick Installation Manual preview
ZyAIR B-100
Brand: ZyXEL Communications Pages: 23
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Brand: Barracuda Pages: 8
ekwb 3831109819395 Manual preview
3831109819395
Brand: ekwb Pages: 10
EVGA inDtube Instructions preview
inDtube
Brand: EVGA Pages: 3
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Brand: 7th Sense Pages: 148
ZALMAN ZM-GWB3 User Manual preview
ZM-GWB3
Brand: ZALMAN Pages: 9
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
Xtreme SNMP-R90 User & Installation Manual preview
SNMP-R90
Brand: Xtreme Pages: 83
Fortec Star Diamond Systems DS-MPE-CAN2L Manual preview
Diamond Systems DS-MPE-CAN2L
Brand: Fortec Star Pages: 36
Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W Series Specifications preview
Scalable Multi-Graphic Videowall Processors MGP 464W Series
Brand: Extron electronics Pages: 2

Brands by name

Popular brands

Load more brands