manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

A-101 

 

Registers Reference

SPI Receive Data Buffer Shadow Register 

(RXSPI_SHADOW)

Use the 

RXSPI_SHADOW

 register for the receive data buffer (

RXSPI

) to debug 

software. The 

RXSPI_SHADOW 

register resides at a different address from 

RXSPI

, but its contents are identical to the 

RXSPI

. When 

RXSPI

 is read via 

the software, the 

RXS

 bit clears and an SPI transfer may be initiated (if 

TIMOD 

= 00). No such hardware action occurs when the shadow register is 

read. The 

RXSPI_SHADOW

 register is a read-only (RO) register accessible 

only by the software and not the DMA. 

For more information, see “SPI 

Receive Buffer Register (RXSPI)” on page A-101.

SPI Receive Buffer Register (RXSPI)

The SPI Receive Buffer register’s address is 0x1004. The reset value for 
this register is undefined. This is a 32-bit read-only register accessible by 
the core or DMA controller. At the end of a data transfer, the 

RXSPI

 regis-

ter is loaded with the data in the Shift register. During a DMA receive 
operation, the data in 

RXSPI

 is automatically loaded into the internal 

memory. For core- or interrupt-driven transfers, programs can also use the 

RXS

 status bits in the 

SPISTAT

 register to determine if the receive buffer is 

full.

SPI Transmit Data Buffer Register (TXSPI)

The SPI Transmit Buffer register’s address is 0x1003.The reset value for 
this register is undefined. This SPI Transmit Data register is a 32-bit reg-
ister which is part of the IOP register set and can be accessed by the core 
or the DMA controller. Data is loaded into this register before being 
transmitted. Prior to the beginning of a data transfer, data in the 

TXSPI

 

register is automatically loaded into the Transmit Shift register. During a 
DMA transmit operation, the data in the 

TXSPI

 register is automatically 

loaded from internal memory.

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Octavo OSD3358-SM-RED Getting Started Manual preview
OSD3358-SM-RED
Brand: Octavo Pages: 28
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Brand: XMOS Pages: 112
Stanwax Laser ILDA Gem Laser projector tool Instructions preview
ILDA Gem Laser projector tool
Brand: Stanwax Laser Pages: 3
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
TANDBERG D5018501 Hardware User Manual preview
D5018501
Brand: TANDBERG Pages: 3
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
A2B Electronics ECX-200 Installation Manual preview
ECX-200
Brand: A2B Electronics Pages: 24
ZALMAN CNPS6000-Al User Manual preview
CNPS6000-Al
Brand: ZALMAN Pages: 6
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
Omron JUSP-NS500 Datasheet preview
JUSP-NS500
Brand: Omron Pages: 6
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117

Brands by name

Popular brands

Load more brands