manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

9-53 

 

Serial Ports

The following bits, listed in bit number order, control serial port modes 
and are part of the 

SPCTLx

 (transmit and receive) Control registers. Other 

bits in the 

SPCTLx

 registers set up DMA and I/O processor-related serial 

port features. For information about configuring a specific operation 
mode, refer to 

Table 9-1 on page 9-10

 and 

“Standard DSP Serial Mode” 

on page 9-11

.

Serial Port Enable.

 

SPCTLx

 bits 0 and 24 (

SPEN_A

 and 

SPEN_B

). This bit 

enables (if set, = 1) or disables (if cleared, = 0) the corresponding serial 
port channel A or B. Clearing this bit aborts any ongoing operation and 
clears the status bits. The SPORTS are ready to transmit or receive two 
serial clock cycles after enabling.

This description applies to I

2

S and DSP Standard Serial modes only.

Data Type Select.

 

SPCTLxx

 bits 2–1 (

DTYPE

). These bits select the com-

panding and MSB data type formatting of serial words loaded into the 
transmit and receive buffers. This bit applies to DSP standard Serial and 
Multichannel modes only. The Transmit Shift register does not zero-fill 
or sign-extend transmit data words; this only takes place for the receive 
shift register.

For Standard mode, selection of Companding mode and MSB format are 
exclusive:

00 = Right-justify; fill unused MSBs with 0s
01 = Right-justify; sign-extend into unused MSBs
10 = Compand using 

_law, (primary channels only)

11 = Compand using A_law, (primary channels only)

For Multichannel mode, selection of companding mode and MSB format 
are independent:

x0 = Right-justify; fill unused MSBs with 0s
x1 = Right-justify; sign-extend into unused MSBs
0x = Compand using 

_law 

1x = Compand using A_law

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Brand: Lab.gruppen Pages: 35
QSC DSP-30 Hardware Manual preview
DSP-30
Brand: QSC Pages: 28
hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Brand: iesy Pages: 9
Altimium CVHH2 User Manual preview
CVHH2
Brand: Altimium Pages: 12
Intel SRCSASPH16I - RAID Controller Hardware Manual preview
SRCSASPH16I - RAID Controller
Brand: Intel Pages: 28
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Brand: Patton electronics Pages: 8
A4Tech G6 Saver User Manual preview
G6 Saver
Brand: A4Tech Pages: 8
DOD 410 SERIES II Owner'S Manual preview
410 SERIES II
Brand: DOD Pages: 12
Avaya VSP 8284XSQ-AC Quick Install Manual preview
VSP 8284XSQ-AC
Brand: Avaya Pages: 2
FabiaTech FB2701 User Manual preview
FB2701
Brand: FabiaTech Pages: 86
OWC ENVOY PRO MINI User Manual preview
ENVOY PRO MINI
Brand: OWC Pages: 7

Brands by name

Popular brands

Load more brands