manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

9-10

ADSP-2126x SHARC Processor Hardware Reference

 

The 

SPCTLx

 register is unique in that the name and functionality of its bits 

changes depending on the operation mode selected. In each section that 
follows, the bit names associated with the operating modes are described. 

Table 9-1

 provides values for each of the bits in the SPORT Serial Con-

trol (

SPCTLx

) registers that must be set in order to configure each specific 

SPORT operation mode. An X in a field indicates that the bit is not sup-
ported for the specified operating mode.

Table 9-1. SPORT Operation Modes

OPERATING MODES

Bits

OPMODE LAFS

FRFS

MCEA

MCEB

SLENx

Standard DSP Serial Mode

0

0, 1

X

0

0

3-32

1

1   Although serial ports process word lengths of 3 to 32 bits, transmitting or receiving words smaller 

than 7 bits at core clock frequency/4 of the processor may cause incorrect operation when DMA 
chaining is enabled. Chaining disables the processor’s internal I/O bus for several cycles while 
the new Transfer Control Block (TCB) parameters are being loaded. Receive data may be lost 
(for example, overwritten) during this period.

I

2

S (Tx/Rx on Left Channel First) 1

0

1

0

0

8-32

I

2

S (Tx/Rx on Right Channel 

First)

1

0

0

0

0

8-32

Left-justified Sample Pair Mode 
(Tx/Rx on FS Rising Edge)

1

1

0

0

0

8-32

Left-justified Sample Pair (Tx/Rx 
on FS Falling Edge)

1

1

1

0

0

8-32

Multichannel A Channels

0

0

X

1

0

3-32

1

Multichannel B Channels

0

0

X

0

1

3-32

1

Multichannel A and B Channels

0

0

X

1

1

3-32

1

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Campbell NL115 Instruction Manual preview
NL115
Brand: Campbell Pages: 42
Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Brand: Sun Microsystems Pages: 6
Omnia Volt Quick Start Installation Manual preview
Volt
Brand: Omnia Pages: 6
IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
Patton electronics 1084 Installation And Operation Manual preview
1084
Brand: Patton electronics Pages: 16
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
3Com Token Ring Getting Started Manual preview
Token Ring
Brand: 3Com Pages: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Brand: ESD Pages: 28
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Brand: ekwb Pages: 7
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
Alarm NX-208E Installation Manual preview
NX-208E
Brand: Alarm Pages: 5
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Brand: Primera Pages: 2

Brands by name

Popular brands

Load more brands