Analog Devices ADRF5515A-EVALZ User Manual Download Page 3

User Guide

UG-1891

EVALUATION BOARD HARDWARE

analog.com

Rev. 0 | 3 of 9

OVERVIEW

The ADRF5515A-EVALZ is preinstalled with connectors (end

launch SMA) and assembled with the 

ADRF5515A

 and its applica-

tion circuitry. All components are placed on the primary side of the

ADRF5515A-EVALZ. An assembly drawing for the ADRF5515A-

EVALZ is shown in 

Figure 8

. An ADRF5515A-EVALZ schematic is

provided in 

Figure 9

.

ADRF5515A-EVALZ LAYOUT

The ADRF5515A-EVALZ is designed using RF circuit design tech-

niques on an 8-layer printed circuit board (PCB). The PCB stack-up

is shown in 

Figure 2

.

Figure 2. Evaluation Board Stack-Up

The outer copper layers are 2 oz (2.7 mil) thick and the inner layers

are 1 oz (1.3 mil) thick. The top dielectric material is 10 mil Rogers

4350B, which provides 50 Ω controlled impedance and optimizes

high frequency performance. The remaining six dielectric layers are

FR4 based filler layers that improve the mechanical strength of the

ADRF5515A-EVALZ and meet the overall board thickness of 62 mil.

All RF traces are routed on the top layer, and the remaining

seven layers are ground planes that provide a solid ground for

RF transmission lines and help to manage thermal rise on the

ADRF5515A-EVALZ during high power operations.

The RF transmission lines are designed using a coplanar wave-

guide (CPWG) model with a width of 18 mil and ground spacing

of 13 mil to have a characteristic impedance of 50 Ω. Ground via

fences are arranged on both sides of a CPWG to improve isolation

between nearby RF lines and other signal lines.

The exposed ground pad of the ADRF5515A, which is soldered

on the PCB ground pad, is the main thermal conduit for heat

dissipation. The PCB ground pad is densely populated with filled

through vias to provide the lowest possible thermal resistance

path temperature from the top to the bottom of the PCB. The

connections from the package ground leads to ground are kept as

short as possible.

POWER SUPPLY INPUTS

The ADRF5515A-EVALZ has five power supply inputs and two

grounds, as shown in 

Table 1

. The dc test points are populated only

on the SWVDDB, VDD1_A, and VDD1_B test points, whereas the

VDD2_A and VDD2_B points are shorted to VDD1_A and VDD1_B,

respectively, via 0 Ω resistors. A single 5 V supply is connected

to the dc test points on the SWVDDB, VDD1_A, and VDD1_B test

points. Ground reference can be connected to the GND or GND1

test point. The typical total current consumption for the ADRF5515A

is 190 mA in receive operation, high gain mode.

Each supply pin for the LNAs of the ADRF5515A-EVALZ is decou-

pled with 1 nF and 10 µF capacitors. A 10 µF capacitor is used on

the supply line for the switches of the ADRF5515A-EVALZ.

Table 1. Test Points for Power Supply Inputs
Test Points

Description

VDD1_A

Supply LNA Stage 1 on Channel A

VDD2_A

Supply LNA Stage 2 on Channel A, do not insert (DNI)

VDD1_B

Supply LNA Stage 1 on Channel B

VDD2_B

Supply LNA Stage 2 on Channel B, DNI

SWVDDB

Supply switches on Channel A and Channel B

GND

Ground

GND1

Ground

The ADRF5515A-EVALZ also has edge mounted Subminiature

Version A (SMA) connectors for power supply inputs, as shown in

Table 2

. These SMA connectors are not populated by default and

can be connected by the user.

Table 2. SMA Connectors for Power Supply Inputs
SMA Connectors

Description

VDD_A

Supply LNA on Channel A

VDD_B

Supply LNA on Channel B

SWVDDB

Supply switches on Channel A and Channel B

Summary of Contents for ADRF5515A-EVALZ










Reviews: