background image

One Technology Way · P.O. Box 9106 · Norwood, MA 02062-9106 · Tel: 781.329.4700 · Fax: 781.461.3113 · 

www.analog.com

Rev 07 Aug 2013 10:33 | Page 1

AD9142A-M5372-EBZ Evaluation Board Quick
Start Guide

Getting Started with the AD9142A-M5372-EBZ Evaluation
Board and Software

What's in the Box

AD9142A-M5372-EBZ Evaluation Board

Evaluation Board CD

Mini-USB Cable

Recommended Equipment List

+5Vdc, Power Supply

2 Sinusoidal Clock Sources

Spectrum Analyzer

Data Pattern Generator Series 2 (DPG2)

Introduction

The AD9142A-M5372-EBZ connects to a DPG2 for quick evaluation of the AD9142A, a high-speed,
signal processing Digital to Analog Converter. The DPG2 automatically formats the data and sends it
to the AD9142A-M5372-EBZ, simplifying evaluation of the device. The Evaluation Board (EVB) runs
from a +5V supply. A clock distribution chip AD9516 is included on this EVB as a clock fan-out and
frequency divider for the DACCLK, REFCLK and DPG2 input clock. Also included is a quadrature
modulator ADL5375 for quick DAC+IQMOD evaluation. Figure 2 is an image of the top side of the
AD9142A-M5372-EBZ.

AD9142A Evaluation Software

The AD9142A Evaluation Board software has an easy-to-use graphical user interface (GUI). It is

Summary of Contents for AD9142A-M5372-EBZ











Reviews: