manualshive.com logo in svg

AMX TDS, Operation/Reference Manual

Share
Download
AMX TDS Operation/Reference Manual Download Page 31

AMX TDS - Terrestrial/Satellite (Standard Definition)

23

AMX TDS (Television Delivery System) 

DTV-TX Transmitters - Front Panel Components

The front panel components are identical on the DTV-TX01-DVB-T and DTV-TX02-DVB-S Transmitters .

Front Panel - ETHERNET 10/100 Port

The ETHERNET 10/100 (RJ45) port on the front panel provides 10/100 BaseT network connectivity via 
Cat5/5e/6 network cable (FIG. 33). Refer to the 

Connecting the Transmitters to the Network

section on 

page 38 for more information. 

DTV-TX02-DVB-S Transmitter (Cont.)

• Common Interface 

Slots 1 & 2: 

Dual Common Interface Slots enable the Transmitter to select encrypted channels 
in cases where this is supported by the broadcaster.

Note: Before de-scrambling content using the Common Interface Slots, ensure that 
you have the appropriate authority/rights to transmit the de-scrambled content on 
your network.

• RESET button:

Press to reboot the Transmitter.

Rear Panel Components:

• RF INPUTs:

Two coaxial (Type F) input connectors accept incoming satellite signals.

Note: The DVB-S unit does not provide LNB power, or a 22kHz tone. Therefore, to 
change polarization or LO frequency, an LBN/22kHz injector is required at the 
head-end. 

• Factory Reset Button: 

The recessed Factory Reset button on the rear panel allows you to perform a full 
factory reset (resets flash and reboots the Transmitter in DHCP mode):

• Press and hold the recessed Factory Reset button while simultaneously pressing 

the Reset button on the front panel.

• Continue to hold the Factory Reset button while the unit is rebooting.

• Release when the Streaming Status LED begins to flash.

• SERIAL (RS232):

DB9 serial connector for local command line interface (RS232 only).

• PWR: 

2-pin mini-phoenix connector provides 12VDC power from the power supply.

Environment:

• Operating Temperature: 32°F - 122°F (0°C to 50°C)

• Operating Humidity: Max. relative humidity - 85% (non-condensing)

Certifications:

• CE

• FCC part 15 Class A

Other AMX Equipment:

• DTV-MA01 TDS Management Appliance (FG1412-01)

• DTV-RX01-SD Receiver (FG1411-01)

• DTV-TX01-DVB-T Transmitter (FG1410-01)

• DTV-RK, Rack Mount Kit for DVB-T/S Transmitters (FG1410-60)

• CC-232 Serial Communication Cable (FG10-752-04)

• 12V Power Supply

FIG. 33  

ETHERNET 10/100 Port

Cat5/5e/6 network cable

Summary of Contents for TDS











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands