sshh
There are two types of installations for the N-Series Wall Controllers: Ring
Adapter (when mounting into an existing electrical box) and Flushmount (when
mounting into an SVSI-provided installation box).
Note: If desired, you can pre-configure the unit before physically installing it. To
do so, simply plug a PoE (Power over Ethernet) enabled Ethernet connection into
the back of the controller and skip to the section Configuring Your New Wall Con-
troller for further instructions.
Important: For ease of installation, only use bootless Ethernet cables when
installing the Controller into the wall. The flexibility is necessary for proper
positioning in the box’s small space.
Mounting Instructions - Ring Adapter Installation
Follow the steps below to mount your new SC-WPC-SM/SC-TC-SM into an
existing dual gang electrical box. The instructions given assume the box is
already installed with Ethernet access running to it.
1. Secure the mounting ring adapter (included in shipment) to your existing
dual gang electrical box with four screws.
2. Connect the PoE-enabled Ethernet cable to the rear connector of the wall
controller.
3. Place the wall controller display into the box and secure it with four screws
(included in shipment).
4. Complete the installation by snapping the AMX faceplate onto the front.
Ring Adapter Installation (SC-WPC-SM/SC-TC-SM)
QUICK START GUIDE
SVSI SC-WPC: Stand-alone, dual-gang IP wall controller (push-button)
SVSI SC-TC:
Stand-alone, dual-gang IP wall controller (push-button
and touchscreen with built-in WiFi)
N-Series Wall Controllers
1. Using the
Wall Controller Installation Cut-Out Template
(enclosed in ship-
ment), mark the position on the wall where the unit is being installed and cut
the opening.
2. Once the opening is cut (and the PoE-enabled Ethernet cable is accessible
through the opening) insert the plastic installation box (included in
shipment). Use the break-out tabs as needed to correctly position the
Ethernet cable.
3. Secure the installation box to the wall with the two captive screws.
4. Connect the Ethernet cable to the rear connector of the wall controller.
5. Place the wall controller display into the box and secure it with four screws
(included in shipment).
6. Complete the installation by snapping the AMX faceplate onto the front of the
Flushmount Installation (SC-WPC-D/SC-TC-D)
Mounting Instructions - Flushmount Installation
Follow these steps to flushmount your new SC-WPC-D/SC-TC-D into the wall.
The steps given assume the installer needs no instruction on running Ethernet
to the installation box or other basics.
Configuring Your New Wall Controller
You will not be able to configure the controller until it is in the same subnet as
the host PC. N-Touch devices are shipped in Auto-IP mode with a default IP
address of 169.254.xxx.xxx. Before attempting configuration, some changes
must be made to the host PC.
Sample steps for IP address configuration (Windows):
1. From the
Control Panel > Network and Internet
dialog box, select
Network
and Sharing Center
.
2. Select
Change adapter settings
.
3. Select the wired interface connected to your AV network.
(Continued)
1. Using the
Wall Controller Installation Cut-Out Template
(enclosed in ship-
ment), mark the position on the wall where the unit is being installed and cut
the opening.
2. Once the opening is cut (and the PoE-enabled Ethernet cable is accessible
through the opening) insert the plastic installation box (included in
shipment). Use the break-out tabs as needed to correctly position the
Ethernet cable.
3. Secure the installation box to the wall with the two captive screws.
4. Connect the Ethernet cable to the rear connector of the wall controller.
5. Place the wall controller display into the box and secure it with four screws
(included in shipment).
6. Complete the installation by snapping the AMX faceplate onto the front of the
wall controller.
Configuring Your New Wall Controller (Continued)
4.Click the
Properties
button.
5.Scroll down in the list to the
Internet Protocol Version 4
(TCP/IPv4)
option. Highlight it
and click the
Properties
button.The screen shown (at
left) is displayed.
6.Enable the
Use the following
IP address
option, and enter the
static IP address
provided to you
by your network administrator.
Logging in for the
First Time
Once connected to the network,
the welcome screen appears on
the N-Series Wall Controller’s
front panel and displays the unit’s serial number, MAC address, and IP address.
1. Using your computer, enter the N-Series Wall Controller’s IP address into your
web browser.
2. The
N-Series Wall Panel Controller Login
screen displays. Use the default
login credentials (username =
admin
/password =
password
)
to log in for the
first time. Upon successful login, the
Settings
page displays (shown at right).
See the section
Using
Panel Builder
for details.
Click
Settings
to
return to this screen.
Click
?
to access
additional
documentation.
See the section
Viewing
Panels on the SVSI
Conductor Mobile App
for
details on the
Users
screen.
See the section
Wireless
Configuration (SC-TC
Units Only)
for details.