Installation Guide
NXD-500IW
5" Water-Resistant Wall/Flush Mount Touch Panel
For more detailed installation, configuration, programming, file transfer, and operating
instructions, refer to the
NXD-500i Operation/Reference Guide
, available online at
www.amx.com
.
Overview
The NXD-500IW widescreen color panel is designed for use in high-humidity INDOOR
environments ranging between 50 and 95% relative humidity. It includes a built-in
microphone, speakers, a mini-USB port for programming and audio output, and one
NetLinx-programmable button. All power is supplied via Power Over Ethernet (PoE),
utilizing a PS-POE-AF PoE Injector (
FG423-80
) or equivalent PoE device. The
NXD-500IW comes in Mystique black (NXD-500IW-MB,
FG2261-09
) and Mystique
white (NXD-500IW-MW,
FG2261-12
).
The NXD-500IW supports Intercom functionality, which allows two communicating
panels (controlled by the NetLinx Master) to transmit full-duplex audio signals over a
network in order to be used as an Intercom system.
Specifications
IP Rating Compliance (Indoor Use Only)
The NXD-500IW is IP Rating 51 compliant. Ingress of dust is not entirely prevented,
but it will not enter in sufficient quantity to interfere with the satisfactory operation of
the device; complete protection against contact. Dripping water (vertically falling
drops) shall have no harmful effect.
Panel Connectors and Wiring
FIG. 2 shows the connectors located on the NXD-500IW Modero panel. The mini-USB
port is used both for programming the touch panel and for audio output. The mini-USB
port automatically detects the presence of a headphone adaptor, allowing the port to
be used for headphone connectivity.
For more information on connection and use of the Panel Connectors, as well as
information on programming and headphone connectivity, please refer to the
NXD-500i Operation/Reference Guide
, available at
www.amx.com
.
Front Bezel Button
The NXD-500IW has only one button on the front of the device, in the center of the
bezel. This button has several uses:
•
Press the button once to start a previously programmed function, or to turn off
the display if not previously programmed.
•
Press and hold the button for 6 seconds to put the device into
Setup Mode
.
•
Press and hold the button for 9 seconds to enter
Calibration Mode
.
•
Press and hold the button for 20 seconds to reboot the panel.
FIG. 1
NXD-500IW-MW 5" Modero Widescreen WallMount Touch Panel
NXD-500IW (FG2261-09/12) Specifications
Dimensions (HWD):
• NXD-500IW (with bezel): 4.15" x 5.59" x 1.97"
(10.50 cm x 14.20 cm x 5 cm)
• CB-TP5 Rough-In/Wallbox (optional): 4.27" x 5.14" x 3.40"
(10.86 cm x 13.06 cm x 8.64 cm)
Power
Requirements:
• PoE Powered - No local Power Supply needed
• Max power draw: 5.5W.
Memory (Factory
default):
• 128 MB SDRAM
• 256 MB integrated Flash Memory (not upgradeable - factory
programmed)
Weight:
• 0.80 lbs (0.36 kg)
Certifications:
• FCC Part 15 Class B
• CE
• IEC 60950
• RoHS
Panel LCD
Parameters:
• Aspect ratio: 16 x 9
• Maximum brightness (luminance): 200 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 250:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.14 mm
• Panel type: TFT Color Active-Matrix
• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame
frequency
• Viewing dimensions: 4.3" x 2.58" (109.2 mm x 65.2 mm)
Active Screen Area:
• 4.25” x 2.55” (10.80cm x 6.48cm)
Viewing Angles:
• Up/Down/Left/Right: 85/85/85/85
IR Reception Angle:
• Horizontal: + 25° (left and right from center)
• Vertical: + 15° (up and down from center)
Supported Audio
Sample Rates:
• 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz,
12000Hz, 11025Hz, and 8000Hz.
Intercom:
• Full duplex VoIP capabilities.
Front Panel Components:
Light Sensor:
• Photosensitive light detector for automatic adjustment of the
panel brightness.
Motion Sensor
(PIR):
• Proximity Infrared Detector to wake the panel when panel is
approached.
Front Bezel Button:
• Provides both access to the
Setup
and
Calibration
pages and
toggles the panel between a “sleep” or “wake” state. This button
is also user-programmable.
Front Bezel Button
Bezel
Speaker
Touch screen
Microphone
NXD-500IW Specifications (Cont.)
Front Panel Components (Cont.)
Microphone:
• Frequency response of 300 to 3400Hz; used for intercom
applications.
Speaker:
• Output of 4Ohm, 2 Watts, with a 300Hz low cutoff frequency.
Side Panel Connectors:
Ethernet 10/100
Port:
• RJ-45 port for 10/100 Mbps communication. The Ethernet port
automatically negotiates the connection speed (10 Mbps or 100
Mbps), and whether to use half duplex or full duplex mode.
Power is supplied through Power Over Internet (PoE). NXD-
500IW panels communicate with the NetLinx Master using the
ICSP protocol over Ethernet. LEDs show communication activity,
connections, speeds, and mode information:
L/A-link/activity
- Yellow LED lights On when the Ethernet cables
are connected and terminated correctly and then blinks when
receiving Ethernet data packets.
SPD-speed
- Green LED lights On when the connection speed is
100 Mbps and turns Off when the speed is 10 Mbps.
Mini-USB
Connector:
• 5-pin Mini-USB connector used for programming, firmware
update, and touch panel file transfer between the PC and the
target panel. The connector is also used for providing audio
output for external speakers.
Operating /Storage
Environments:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 5% - 95% relative humidity
(non-condensing)
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
• Indoor Installation and Operation ONLY
Included
Accessories:
• NXD-500IW Installation Guide (
93-2261-09
)
Other AMX
Equipment:
• CB-TP5i Rough-In/Wallbox (
FG038-11
)
• Back Cover for the CB-TP5i Rough-In/Wallbox (
FG038-12
)
• PS-POE-AF PoE Injector (
FG423-80
)
• CC-USB Type-A to Mini-B 5-wire programming cable
(
FG10-5965
)
• USB to Headphone Adaptor (
FG5966-23
)
FIG. 2
Connector layout on the NXD-500IW
Ethernet 10/100 port
Mini-USB port
Back box
