Quick Start Guide
AutoPatch
DVI-D to RGBHV Converters
Overview
DVI-D to RGBHV converters are available in two models: a standalone module and
an accessory board in an AF-10 (FIG. 1). This guide contains complete information for
the module. For the accessory board, see the AF-10 Quick Start Guide for instructions
on adding or replacing boards and for AF-10 specifications. All quick start guides are
on the AMX AutoPatch Software & Documentation CD and at www.amx.com.
Product Specifications
Module Mounting Options
•
Desktop – attach the rubber feet (included) on the bottom of the module.
•
Rack Trays & Mounting Brackets – contact your AMX representative for details.
Installation
Typical System Setup
The DVI-I connector on the converter routes a DVI-D signal and accepts cable with
either DVI-D or DVI-I connector plugs. The module and the AF-10 board support the
eight resolutions listed in the table to the right above.
Supported Resolutions
The video card in the system must be set to one of the resolutions and its
corresponding refresh rate in the table below.
* Some monitors may not accept the maximum refresh rate.
** This refresh rate exceeds DVI specifications.
To change the Source PC’s video card resolution/refresh settings on
Windows operating systems:
1.
Minimize all applications on the Source PC.
2.
Right click on the desktop.
3.
Select Properties from the shortcut menu.
4.
Select the Settings tab in the Display Properties dialog box.
5.
Adjust the Screen area setting (resolution) to match one of the eight supported
resolutions listed in the table above.
6.
Click Advanced.
7.
Select the Monitor tab.
8.
Adjust the Refresh Frequency, which is expressed in Hertz (see table above). If
the frequency setting is not located under the Monitor tab, try selecting other
available tabs.
9.
Click Apply, and then click OK on each dialog box to exit.
10.
Power down the PC.
11.
Install the converter (see “Installation” below).
12.
Reapply power to the PC.
Installation
•
Module – directions for attaching connectors are below
•
AF-10 Board – directions for attaching connectors are on the reverse
•
Pinouts – DVI-I (FIG. 6) and HD-15 (FIG. 7) connector pinouts are on the
reverse.
Module
To attach connectors:
1.
Insert the DVI-D and HD-15 cable connector plugs into the receptacles on the
module (FIG. 4).
2.
Plug the power cord into the power jack on the module and into the power
source.
FIG. 1
Module FG1010-06 AF-10 board FG1040-485
Product Specifications
Approvals
CE, UL, cUL
Power
–
Module
+9 VDC, 500 mA wall transformer, 2.1 mm DC power jack
Power – AF-10
120 VAC / 240 VAC
Humidity
0 to 90% non-condensing
Operational Temperature
32° - 110° F (0° - 43° C)
Dimensions
–
Module
5.22 in. (13.26 cm) depth
5.82 in. (14.78 cm) width
1.42 in. (3.61 cm) height without feet
Weight
–
Module
Approximately 1.5 lbs (0.68 kg)
Specification
DVI-D 1.0 (single link)
DDC/EDID Support
Provided by converter
HDCP Support
No
Connectors
DVI-I (supports DVI-D signal) and HD-15
FIG. 2
System setup with converter module
FIG. 3
System setup with AF-10 converter boards
(not to scale)
DVI-D to RGBHV
Converter Module
DVI-D to RGBHV
AF-10 Board
Source PC
Destination monitor
Module (FG1010-06)
120V
AC
/240V
AC
25 W
att /
2
A
Max.
Source PC
Destination monitor
Boards (FG1040-485)
AF-10 (FG1040-10)
Supported Resolutions
Resolution
Refresh Rate*
640x480
120 Hz max.
800x600
120 Hz max.
1024x768
120 Hz max.
1152x864
100 Hz max.
1280x768
85 Hz max.
1280x960
85 Hz max.
1280x1024
85 Hz max.
1600x1200
75 Hz max.**
FIG. 4
Attach DVI-D, HD-15, & power cable connectors
HD-15 cable
DVI-D cable
Power cable
DVI-I
receptacle