AMX Epica DGX 144, Instruction Manual

Page: 50 / 107

Epica DGX 144 SC Fiber Boards
46 Epica DGX 144 Instruction Manual
Specifications Epica DGX 144 SC Fiber
Applies to DGX SC Fiber input board FG1055-440 and DGX SC Fiber output board FG1055-450.
Compatible AMX AutoPatch DGX SC Fiber modules:
FG1010-200-01 – AVB-TX-DGX-HD15-SC Fiber
FG1010-210-01 – AVB-TX-DGX-DVI-SC Fiber
FG1010-400-01 – AVB-RX-DGX-SC Fiber-RGBHV
FG1010-410-01 – AVB-RX-DGX-SC Fiber-DVI
Note: Either TX module can be used in conjunction with either RX module.
* 96 kHz audio is only available when the source video resolution is 800x600 @ 60 Hz (40 MHz pixel clock) or
greater. Otherwise, the maximum is 48 kHz.
**3,000 ft. cable requires 50/125
μ
m OM2 class low loss fiber cable. Transmission distance will vary (more or
less) depending on the type/quality of fiber used, fiber bandwidth, cable bend radius/kinks, splicing quality and
quantity, and chromatic or modal dispersion.
***480i and 576i are only available when being transmitted from a DGX HD-15 TX as a Y-Pb-Pr signal.
Important: These boards are compatible only with other AMX AutoPatch products that support
the DGX single fiber technology. They are not compatible with third-party optical distribution
amplifiers or multimode to single-mode converters.
AMX reserves the right to modify its products and their specifications without notice.
Epica DGX 144 SC Fiber Specifications
Parameter Value
Compatible AutoPatch Fiber Products DGX HD-15 TX and RX, DGX DVI TX and RX, other AMX AutoPatch
DGX SC Fiber signal management products
Safety Certifications
(DGX SC Fiber output board only) Class 1 Laser Product (Class 3R Laser Product when fiber is
disconnected from the unit) IEC 60825-1, 2001
Signal Types over Fiber Video, audio, serial data
Video signal must be present to pass audio and serial data
Resolution Support 640x480 @ 60 Hz up to 1920x1200 @ 60 Hz
Audio Support Analog stereo or S/PDIF (S/PDIF up to 96 kHz sample rate*)
Serial Data Support Unidirectional RS-232, up to 115.2 k baud
Fiber Cable Types Multimode Simplex (with SC termination)
50/125
μ
m (preferred) or 62.5/125
μ
m
Fiber Cable Length Up to 3000 ft. (914.4 m) in with 50
μ
m cable**
Up to 3000 ft. (914.4 m) out with 50
μ
m cable**
Up to 1500 ft. (457.2 m) in with 62.5
μ
m cable
Up to 1500 ft. (457.2 m) out with 62.5
μ
m cable
Interlaced Resolution Support 1080i 60, 59.94, 50 (fields per second)
576i 100, 50 (fields per second)***
480i 60 (fields per second)***
Optical Budget 9.75 dBm (typical) between DGX TX and DGX SC Fiber input board
9.75 dBm (typical) between DGX SC Fiber output board and DGX RX
Optical Modulation Amplitude (OMA): -6.25 dBm (typical)
Optical Modulation Amplitude (OMA) Sensitivity: -16.0 dBm (typical)
Power (max. output of laser radiation)
(DGX SC Fiber output board only) 4.08 mW
Fiber Connector (on board) SC Optical