background image

a

 ALR-AMP-8 Alero 8 Zone Power Amplifier

Important Safety Instructions

1.

Read the instructions.

2.

Keep the instructions.

3.

Heed all warnings.

4.

Follow the instructions.

5.

Do not use this apparatus near water.

6.

Clean this apparatus only with a dry cloth.

7.

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that 
produce heat.

9.

Do not defeat the safety purpose of the grounding type plug. The grounding plug has two blades and a third grounding 
prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician 
for replacement of the obsolete outlet.

10.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point 
where they exit from the apparatus.

11.

Only use attachments/accessories specified by the manufacturer.

12.

Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is 
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.

Unplug this apparatus during lightning storms or when unused for long periods of time.

14.

Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as 
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has 
been exposed to rain or moisture, does not operate normally, or has been dropped.

15.

The appliance coupler is used as the disconnect device and shall remain readily operable.

Please adhere to all of the following safety instructions:

WARNING! To reduce the risk of fire or electric shock, do not expose this apparatus to 
rain or moisture.

WARNING! This apparatus shall be connected to a MAINS socket outlet with a protective 
earthing connection.

WARNING! This apparatus shall not be exposed to dripping or splashing, and no objects 
filled with liquids, such as vases, shall be placed on the apparatus.

DANGER! No user serviceable parts inside. Service is to be performed only by AMX. 

Safety Symbol Definitions 

The exclamation point within an equilateral triangle is intended to alert the user to the presence of 
important operating and maintenance (servicing) instructions in the literature accompanying the 
product.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to 
the presence of non-insulating, dangerous voltage within the product's enclosure that may be of 
sufficient magnitude to constitute a risk of electric shock to persons.

Summary of Contents for ALR-AMP-8

























Reviews: