QUICK START GUIDE
ACV-5100
Acendo Vibe
™
Conferencing Sound Bar with Camera
Overview
The ACV-5100 features a hinged Wall Mount Bracket, which allows easy installation as
well as access to the Connector Bay without having to dismount the unit. The Wall
Mount Bracket features a cutout for cable routing and straps for cable management.
Note
: Do not lift the ACV-5100 by the camera or rest the unit on the camera.
Credenza Installation
Note
: To ensure highest possible sound quality, the rubber feet on the bottom panel
must remain in place for surface-mount installations.
The ACV-5100 can sit on a hard, flat surface such as a credenza, tabletop or desk.
When choosing a surface location, consider a space that will not interfere with
workspaces or other installed devices. Connect cables as necessary - see the
Connections
section for details.
Wall Mount Installation
For best aesthetic in wall mount installations, remove the rubber feet from the bottom
panel: carefully peel each foot off of the bottom surface.
Removing the Wall Mount Bracket
1.
Open the Wall Mount Bracket (held closed by internal magnets).
2.
Press and hold the
Release Button
to slide the Bracket out (over the button) to
disengage the pins on the Bracket from the hinges on the unit (FIG. 2).
3.
Lift the Wall Mount Bracket off of the hinges to remove (FIG. 3):
Wall Mount Considerations
•
Distance between conference table and display
:
The closer the table is to the
wall-mounted display. the lower the display should be mounted. As a general
guide, the display should be mounted between 40” and 48” from the floor.
•
Avoid obstructing the camera view
:
If the display protrudes from the wall more
than the ACV-5100, then additional spacing between the display and the
ACV-5100 may be needed.
•
Position camera for full visibility
:
In small rooms, it may be necessary to manually
tilt the camera up to maximize visibility for all participants.
Using the Bracket Mounting Guide
The Wall Mount Bracket features instructions etched on the inner surface that describe
how to position the ACV-5100 beneath a wall-mounted display to avoid obstructing the
camera view (FIG. 5):
1.
Remove the Bracket from the ACV-5100 (see FIG. 7 on page 9).
2.
Turn the Bracket vertically and place against the wall, centered directly beneath
the wall-mounted display.
3.
Align the top of the Bracket (see
Bottom of Display
) with the bottom surface of the
display.
4.
Use the top edge of the notch in the Bracket (see
Top flat surface of Acendo Vibe
to determine the closest placement for the ACV-5100 beneath the display. Mark
the mounting surface.
5.
Align the top flat surface of the ACV-5100 with the mark made in step 4.
6.
Mount the Bracket using mounting screws and optional mounting spacers (see
FIG. 6).
Mounting the Wall Mount Bracket and Attaching the ACV-5100
1.
Use the Wall Mount Bracket as a template to mark the locations for the four
mounting screws (not included). Use mounting screws and hardware appropriate
for the surface being utilized to secure the Bracket to the wall.
Optionally, if not hiding them behind the drywall, place the four included Wall
Mount Spacers between the Bracket and the wall to create a 5mm gap for
routing flat cables (see FIG. 6).
2.
Attach the ACV-5100 to the Bracket by sliding the pins on the Bracket into the
hinges on the rear of the main unit (see FIG. 3):
a. Position the ACV-5100 with the bottom panel facing the wall and align the
hinges on the main unit with the pins on the Bracket.
b. Carefully slide the pins into the hinges, until the Bracket snaps into place.
Note
: Press the Bracket into place so that the last pin depresses the Release
Button, allowing the pins to slide into the hinges (see FIG. 3)
c. With the ACV-5100 attached to the Bracket, rotate the unit up to its seated
position. Note that the Bracket snaps shut and is held closed via internal
magnets.
Note
: Ensure that cables do not obstruct the complete closing of the unit.
FIG. 1
ACV-5100 (FRONT/REAR VIEWS)
PRODUCT SPECIFICATIONS
MODELS AVAILABLE
• ACV-5100GR, Grey (FG4151-00GR)
• ACV-5100BL, Black (FG4151-00BL)
INCLUDED ACCESSORIES
• 15V
/ 4A.Power Supply
• Remote Control
• 6’ USB 2.0 Cable
• 5mm Wall Mount Spacers (4)
• Lock-Down Screws (2)
DIMENSIONS (HWD)
• 5" x 23 1/2" x 3 15/16" (76 mm x 590 mm x 100 mm)
• Depth with optional wall mount spacers: 4 1/8” (105 mm)
WEIGHT
6.45 lbs (2.93 kg)
ACTIVE POWER REQUIREMENTS
• ~100-240V, 1.3A max
• Only use the included power supply
REGULATORY COMPLIANCE
FCC 47 CFR Part 15, Subpart C / Subpart B (emissions)
EN 55024, EN 60950-1, IEC/EN/UL 60065:2014
ENVIRONMENTAL
• Temperature (Operating): 32° F to 113° F (0° C to 45° C)
• Temperature (Storage): -4° F to 158° F (-20° C to 70° C)
• Humidity (Operating): 5% to 85% RH non-condensing
OPTIONAL ACCESSORIES
• CBL-USB-FL2-16, USB 2.0 16ft Extension Cable (FG10-2220-16)
• CBL-USB-FL2-33, USB 2.0 33ft Extension Cable (FG10-2220-33)
• ACR-5100, Meeting Collaboration System (FG4051-00)
FIG. 2
ACV-5100 BOTTOM VIEW - OPENING THE WALL MOUNT BRACKET
FIG. 3
ACV-5100 BOTTOM VIEW - REMOVING THE BRACKET
Camera
Front
Rear
Rubber feet (removable, x2)
mounting holes (x4)
Wall Mount Bracket
Side Panel
Keypad
Cable Pass-Thru
Wall Mount Bracket
Hinges/Pins
Release Button
Connector Bay
Wall Mount Bracket
Pins (x4)
Hinges (x4)
Slide pins in to install
Slide pins out to remove
Release Button
FIG. 4
ACV-5100 WALL MOUNT CONSIDERATIONS
FIG. 5
USING THE MOUNTING GUIDE
FIG. 6
WALL MOUNTING THE ACV-5100
40-48” from floor
Camera lens should be
positioned beyond the display
to avoid obstructing the view
Display
ACV-5100 Camera
Display
front
(side view)
Mounting Bracket
Mounting Guide
(etched into surface)
(top view)
ACV-5100
Display
Mount the Bracket to the
wall via 4 mounting screws
Attach the ACV-5100 to the
Bracket via hinges & pins
b
a
mounting screws
(x4, not included)
mounting spacers (x4, optional)
Note: Use M4 or #8
mounting screws
Cable Pass-Thru
