13
the appliance or the Customer care office of the manufacturer.
KEEP THESE INSTRUCTIONS CAREFULLY!
SYMBOLS USED IN THESE INSTRUCTIONS
CAUTION
-Indicates a potentially dangerous situation.
- Non-observance may lead to slight or minor injuries.
NOTE
- Indicates information intended to give the user a better under-
standing.
ADDITIONAL INFORMATION
”FIG.A” : Reference to an illustration, for example ”illustration A “
PRODUCT DESCRIPTION - INTENDED USE
AMTRA KLIMA NANO PRESET (15-25-50W and in all watta-
ges in which it is produced), referred to in the following as
”appliance”, may only be used as specified in the following:
-As a preset automatic heater for aquariums, turtle tanks or pa-
ludariums.
- Observing and respecting its technical characteristics.
The following restrictions apply to the device:
- For indoor use only.
-Only operate with water at a temperature b4 °C and
+35 °C
INSTALLATION AND CONNECTION
NOTE
- Connect the appliance only when it is completely immersed in water
-The pre-set temperature is reached within a few hours only if the
calorific power of the device is suitable for the aquarium volume
and the difference in temperature between the environment and
the operating temperature of the device. For a correct choice refer
to ”FIG.D”
Dear customer, thank you for purchasing AMTRA KLIMA NANO PRE-
SET, a fully submersible automatic heater suitable for use in aqua-
riums, paludariums and turtle tanks. Place the heater fully sub-
merged in water in a position with good water circulation by fixing
it firmly to the glass using the suction cups supplied. The appliance
can be positioned both vertically and horizontally (for example for
use in turtle tanks with low water levels) always making sure that
the entire heating element is completely submerged by water.
Take care to create a drip loop along the power cable as shown
in ”FIG.B”.
The appliance can be installed both with and without the protecti-
ve case. To open the protectivecase, proceed as shown in ”FIG.C”
by pressing the central part of both sides of the shell at the same
time.
COMMISSIONING / START-UP
CAUTION
Risk of injury due to hot surface. Parts of the body can be burned or
there is a danger of fire. Before any work, disconnect the appliance
from the mains and then allow it to cool down.
Once the appliance has been correctly positioned, wait
about 30 minutes before starting it so that the inter-
nal thermostat can adjust to the water temperature.
SWITCHING ON: when the appliance is connected
to the mains, the appliance starts up immediately.
SWITCHING OFF: disconnect it from the mains. To avoid shock after
unplugging it, wait about 30 minutes before taking it out of the
water so that all surfaces can cool down adequately.
!
!
i
i
Summary of Contents for A6076081
