![background image](http://html1.mh-extra.com/html/amplivox/s505a/s505a_user-manual_2935120002.webp)
2
NO
TOOL
ASSEMBLY
OF
LECTERN
OPERATION
OF
ADJUSTABLE
LECTERN
This lectern adjusts from 38 inches to 44 inches measured from the
amplifier side. To adjust the lectern height:
1.
With one hand flat in the center of the table holding it down
loosen the adjustable height knob with the other hand.
2.
You may extend the lectern up to its maximum height of 44 inches.
3.
To lower the lectern, lightly press down on the reading table
until the desired height is reached and retighten the
height
-
locking knob.
TIP: The knob locks at any height by tightening it. The lectern
will adjust from 44 inches down to 38 inches when
measured from the amplifier side.
ADJUSTABLE
HEIGHT
DIAL
USE
TO
ADJUST
LECTERN
HEIGHT
FROM
38
TO
44
INCHES
.
CONTROL
PANEL
BASE
MOUNTING
FLANGE
READING
TABLE
FLEXIBLE
GOOSENECK
MICROPHONE
CENTER
COLUMN
Please read all instructions first and then follow the steps below.
Your lectern may not contain all of these features.
BASE
ASSEMBLY
1. Remove center column from the
shipping carton and place as
shipped (speakers face down) on
the floor or on a suitable sturdy
table. If assembling on floor, raise
bottom end of lectern to make fas-
tening base to lectern easier.
2. Remove and unpack the base from the
shipping carton.
3. Position base with the two locking
wheels facing the back of the lectern.
Assemble the base to the column by
using four of the 2 inch long knurl knob
screws supplied with the lectern.
TIP: Do not completely tighten each
screw as you place it through the base
and into the column. Wait until all four
screws have been put into the proper
position and then tighten them up.
4. Turn the base and column assembly
upright. If assembled on a table, place
the unit upright on the floor.
READING
TABLE
ASSEMBLY
1. Remove and unpack the lectern read-
ing table.
2. Attach the table to the top of the col-
umn. This is accomplished by placing
the table top on the column base and
lining up the corners.
TIP: the corners need to be lined up in
order to get the screws in the table top.
3. Fasten the reading table to the column
with the 4
-
1 inch long knurl knob
screws supplied. The knob screw goes
up into the reading table through the 4
holes in the column
SPEAKER GRILLE
1.
Remove and unpack the speaker
grille..
2.
Attach the speaker grille to the front of
the lectern by pushing the plastic posts
in each corner of the grille into the 4
cups.
ASSEMBLY
OF
FLEXIBLE
GOOSENEC
MICROPHONE
:
The
MIC
CORD
comes pre
-
wired to the amplifi-
er but needs to be assembled into the
MOUNT-
ING
FLANGE
located in the far left corner of the
READING
TABLE
.
Take the plug end of the microphone cable and
insert into the rubber boot of the
MOUNTING
FLANGE
from underneath. Push plug end all
the way through the rubber boot.
Now take
GOOSENECK
MICROPHONE
and connect to the plug end of the ca-
ble. Notice that the microphone connect-
or has three small (3) pins inside of the
connector.
These pins can bend if you
are not careful
. Align these pins with
the three (3) holes in the plug end of the
cable and push together until microphone
is completely seated onto the plug.
Now carefully take excess cable and
push back through rubber booth first,
then insert the microphone only far
enough that it is able to stand upright
without falling over.