Amphenol RESMLAC 8US CAPS SX User Manual Download Page 4

RESMLAC 8US CAPS SX - UM rev. 1.0 

Page 4 of 12   

 

   Last Rev: 21-Jan-13 

Amphenol

 – 948, Promenade de l‘Arve – B.P. 29 – 74311 THYEZ Cedex – France - +33(0)4.50.89.28.00 – 

www.rjswitch.com

 

 

Section 2 

Hardware 

 

Overview 
 

The switches can be mounted directly to a flat surface or to a wall. Refer to the mechanical 
drawing below. Its high protected enclosure makes it able to withstand immersion (IP67 
rating).

 

The Ethernet connections come out from rugged MIL-STD-38999 connectors.  

 

Front Panel 
Display 

The following describes the front panel, and LED indicators of the 
RESMLAC8USCAPSSX. 

 

Note: the Handles are not represented. 

 

LED Indicators 

The Single LED indicator on the front panel shows the operative status of the switch.  
Once the LED is turned on, the switch is powered and ready-for-use.  
This LED will be on solid green when proper power has been applied to the unit.  
Each port has 2 LEDs indication:  
 

 

Link / Activity (Off – there is no link, Steady Green – There is a device connected, 
Flashing Green – there is data transmission)  

 

 

Speed (Orange for 100Mbps, Off for 10Mbps)  

Summary of Contents for RESMLAC 8US CAPS SX













Reviews: