background image

CONNECTING THE UNIT - AUDIO INPUTS / OUTPUTS

PAGE 6

AMPERES AX3700

IN

-

IN

+

O

U

T+

IN

-

IN

+

O

U

T-

O

U

T-

IN

+

IN

-

CHANNEL 1

CHAN

2

STANDBY

AMP

AN. 1

ON

CHAN. 2

ON

CHAN

O

CHAN. 4

ON

CHAN. 5

ON

HAN. 6

ON

H

IG

H

CASC

E

CHANNEL 4

+

- G + -

OUTPUT

INPUT

CHANNEL 3

+

- G + -

OUTPUT

INPUT

CHANNEL 2

+

- G + -

OUTPUT

INPUT

CHANNEL 1

STANDBY

+

- G + -

+

- G

OUTPUT

INPUT

OUTPUT

OPEN

OPEN

LINK

LINK

SIGNAL

OPEN

LINK

LINK

SIGNAL

OPEN

LINK

LINK

SIGNAL

NPUTS/OUTPU

CHANNEL / AM

ETECTION SWITCHES

SWITCH TO O

OR UNUSED CHANNEL

FAULT

CONT.

3A NO

MAX

UDIO SIGNAL INPUTS / OUTP

RS 485

A B

FROM MIXER 

BGM SOURCE 

3

FROM MIXER 

BGM SOURCE 

2

FROM MIXER 

BGM SOURCE 

1

LINK

SWITCH 1

LINK

SWITCH 2

LINK

SWITCH 3

TO

AMPLIFIER

INPUT 4

TO

AMPLIFIER

INPUT 3

TO

AMPLIFIER

INPUT 2

TO

AMPLIFIER

INPUT 1

TO

STANDBY

AMPLIFIER

INPUT

The above shall be for a setup of :

Amplifier 1 and 2 with same input source ; thus only input port of channel 1 is connected.

The Link Switch 1 is switched to link position.

Amplifier  3  and  4  shall  have  separate  BGM  source  and  their  outputs  shall  be  connected  to  the 

respective amplifier inputs. 

Link Switches 2 and 3 shall be at OPEN position.

IF ONLY A SOURCE IS TO BE CONNECTED TO ALL AMPLIFIERS :

In the case that a single source is used for the whole installation, connect only to channel 1 and set all 

the link switches to LINK position.

NOTE :

Input and Output signal from AX3700 shall have unity gain. Therefore a single source shall be limited to 

max 6 output channels. If a source were to be connected to more than 6 amplifiers, it is recommended 

that a distribution amplifier is used before connecting it to the AX3700 input port.

Having  a  source  connected  directly  to  more  than  6  amplifiers  may  cause  impedance  drop,  probably 

causing distorted sound quality as well as signal drop.

Summary of Contents for AX3700













Reviews: