GASGUARD IS CONTROLLER Issue: R2, Date: 26/09/2011, CRN: 7502
Page 23
4
Programming
4.1
Programming Overview
All operating functions of the Gasguard System can be programmed through the keypad on the controller by
entering into the Configuration Menu. Note that some keys have more than one function.
4.1.1
Key Pad Functions in Modify Menu
By using the
key in the modify menu, the operator can scroll the alpha-numerals or pre-set values.
By using the
key in the modify menu, the operator can move the cursor across to the next digit.
By using the
key in the modify menu, the operator can save the new settings.
By using the
key in the modify menu, the operator can escape out of the modify zone, and not save
the new settings.
4.1.2
To enter the Configuration Menu:
1.
From the Monitoring Screen, press the
key to scroll up to level 7 ‘Configuration View and Modify’ Menu.
2.
Press the
key to enter into the ‘Do you want to continue?’ screen.
3.
If YES, press the
key to gain access; if NO, press the
key to exit.
4.
On the ‘Enter Password’ screen, use the
key to scroll through the numbers.
5.
Then use the
key to move the cursor to the next digit.
6.
Once the password has been entered, press the
key to access the ‘Calibration Menu’.
The password is factory set at 9990. This can be changed in Configuration Menu shown on page 18 of this manual.
4.2
Channel Configuration Menu
To view and modify the Channel Configuration settings use the following procedure. This procedure applies to the
configuration of all four channels
1.
When ‘Channel 1 Configuration Menu’ is displayed, press the
key to enter the menu.
2.
There are 23 levels under each channel, 22 of them can be modified to suit the user’s requirements.
3.
By using the
or
keys, the programmer can scroll through the menu.
4.
By using the
key, the programmer can enter into the displayed menu or save the new settings.
5.
Using the
key will allow the programmer to escape out of the modify zone
4.2.1
Input Type
The first level is read only and displays the ‘Input Type’, which is set by the manufacture. For example; 4-20 mA or
0.4-2.0 V inputs.
4.2.2
Set Input Status
Enables Channels to be selected ON or OFF
1.
To modify ‘Status’ press the
key to enter
2.
Use the
key to toggle between ON and OFF, i.e. Channel ON or OFF
3.
To save, use the
key
4.
To escape, use the
key.
Summary of Contents for gasguard
